Can you put a shut off valve on copper pipe?

Quote from the video:
Quote from Youtube video: Around the copper pipe that we're going to cut we're going to approximate where the valve is going to go in to replace. The valve that will no longer shut off.

How do you install a shut off valve on main water line?





Quote from the video:
Quote from Youtube video: And comes straight up to your house. To your shut off valve. But that's not always the case sometimes it might tee off or kind of jog a little bit and go to a valve manifold or a hose bib.

How do you install a shut off valve on an existing PVC pipe?

Quote from the video:
Quote from Youtube video: Use these types of pipe cutters. If you're working on CPVC. A like I am and cut the pipe as close as possible to the old shutoff valve next use sandpaper and sand a little bit to remove debris.

Can you tap into an existing water line?

To tap into existing copper lines, shut off the water. With a tubing cutter cut an opening in each pipe that is about an inch shorter than a tee fitting. Dry-fit the tees. If the pipes are rigidly installed, remove a clamp or two so you can pull the pieces apart slightly.

Can a sharkbite valve be used for main water shut off?

Shark bite valve will be fine. Just make sure you clean the copper pipe thoroughly so there are no rough edges or bits of solder left.

How do you install a water shut off valve on a PEX?





Quote from the video:
Quote from Youtube video: Cut the PEX tube. So the end is square. And free of any burrs or damage or buildup on the surface. Next slide the crimp ring over the tube.

How do you install a saddle valve on a copper pipe?

Quote from the video:
Quote from Youtube video: And this is self piercing it has a needle valve that is going to cut its own hole into the copper tubing. And then as we unscrew this allow the flow of water to go into our humidifier.

How do you tap into a copper water pipe?

Quote from the video:
Quote from Youtube video: So today I'm going to be tapping into a three-quarter inch copper waterline and I'm going to use tektites lip tea to do. It. So this is how it pretty much stacks up you need three quarters of an inch

How do you put a tee on a water line?

Quote from the video:
Quote from Youtube video: You do need some movement to be able to get a new fitting in a pipe like that. So the way you do it is by using a slip coupling that's a normal cup load that is a solid o-ring fitting coupler.

What can I use instead of a saddle valve?



A similarly DIY-friendly but more reliable alternative to a saddle valve is a push-fit tee connector designed for ice makers and water dispensers. You install these by cutting out a short section of pipe and installing the tee right into the water line, then adding the small supply line leading to the appliance.

Are SharkBite fittings reliable?

John Guest quick-connect and SharkBite fittings are both reliable and awesome fittings for emergency fixes. Even though Quick-Connect and SharkBite fittings are rated for use underground and behind walls, soldering pipes may be the smarter choice.

What is a slip tee for?

The “Slip T” PVC fittings, also know as a TL, pass through tees, or slip sling tees are commonly used in building PVC structures where you don’t want to compromise the strength of the pipe by cutting it. With no stops in the top of the Slip T, you can simply slide it onto the pipe where you want it.

How do you use a SharkBite shut off valve?



More videos on YouTube

  1. Turn the water off at the main valve for the home.
  2. Open a few faucets to drain water out of the lines.
  3. Cut the water line just before the shut-off valve.
  4. Ream and de-bur the cut pipe end.
  5. Mark the pipe for the correct depth.
  6. Push the new fitting into place.
  7. Turn the water back on.


How do you use a SharkBite slip tee?

Quote from the video:
Quote from Youtube video: Simply slide the end of the t mark slip end over the copper as far as it will go using a disconnect clip on the slip end of the fitting. Slide the T back over the adjoining piece of copper.

How do you install a SharkBite valve on an existing copper pipe?

Quote from the video:
Quote from Youtube video: The white tubes. Inside these sharkbite fittings are called pipe stiffeners. You can leave them in there for copper pipes you simply push the sharkbite fitting onto the copper pipe to the appropriate.

Are SharkBite shut off valves good?



5.0 out of 5 stars It’s a Sharkbite and they are great! This has to be one of the all-time greatest inventions. This (and PEX) makes plumbing so much easier than 15 years ago when you had to sweat copper. I was replacing a tub/shower and installed these so I could have localized shut-offs.

Do shark bites work on copper?

SharkBite brass push-to-connect fittings are compatible with PEX, Copper, CPVC, PE-RT and SDR-9 HDPE pipe. SharkBite fittings come with a PEX stiffener pre-loaded into the fitting for PEX, PE-RT and SDR-9 HDPE. The PEX stiffener does not need to be removed for Copper or CPVC applications.