You can use one sensor for each light (looks weird but cheaper than below) — buy sensors that fit the standard gang wall plate and buy a two-gang wall plate to cover both. Alternatively, you could move both to a single occupancy sensor using a “dual relay” occupancy sensor.
Can you put a motion sensor on a three way switch?
When using in a 3-way application use one sensor and one standard 3-way switch. Cannot be used with another sensor, or in a 4-way application. WARNINGS AND CAUTIONS: If you are not sure about any part of these instructions, consult an electrician.
Can you wire a motion sensor to multiple lights?
Answer: Yes, you can add motion sensors to existing lights. Moreover, it applies to multiple lights too. However, a remote motion tracker is a better deal. Besides, not only lights, you can connect them with any electric tools.
Can a motion sensor light be on a switch?
Vacancy Switches. Motion sensor switches can automatically turn the lights on or off or both. Both occupancy and vacancy switches leave the lights on if they detect motion in the room, so if you’re perfectly still, they might turn the lights off.
Can you put a motion sensor on a 4-way switch?
You cannot replace a 4-way switch with the sensor you have. The sensor you are using can either function as a 2-way or 3-way switch, it does not function as a 4-way switch. This is what a typical 4-way circuit looks like.
Can you put a motion sensor on a two way switch?
Yes, you can, under code, but you will also need to have ‘real’ switches also installed. As far as the second part write on a bit of paper, in marker, and stuff it in the the motion sensor junction box.
Can I add motion sensor to existing light?
It is possible to add motion to existing outdoor lights. Doing so is simple, in fact, you can even add motion detection without performing one ounce of wiring.
Do motion lights need a switch?
A motion sensor light does not need a switch, but it’s still a good idea to add one. A switch ensures that the light won’t turn on unless you actually want it to. If you want the light to stop responding to movement, you will have that option if you’ve installed a switch.
How do you wire a motion sensor to an LED light?
How to Add Motion Sensors to Existing Outdoor Lights
- Pick an outdoor motion sensor kit online. First, make sure the existing light has an opening to screw into.
- Turn the power off to the light, and remove the cover. …
- Remove the insert. …
- Run the wires into the light. …
- Connect the wires. …
- Adjust the sensitivity.
How do you hook up a motion sensor?
Steps:
- Turn off the power at the main breaker switch.
- Remove the old light fixture and replace it with the new motion-sensor lights, connecting the white wire to white and the black wire to black with the wire nuts.
- Tuck all the wires neatly into the socket.
- Points the bulbs and the sensor in the desired directions.
Are motion sensor lights worth it?
Motion-activated light switches can save homeowners money if installed in medium-to-low traffic rooms like closets, guest rooms, storage rooms, utility closets, and bathrooms. In other cases, it may not be worth the investment so homeowners should stick with traditional switches, like the one shown here.
What is the red wire for on a motion detector light?
The red wire must go to the switch leg (the wire actually powering the light fixture) for the switch to operate properly. It won’t destroy the switch if wired backward, but it won’t work right, either.
How do you install an outdoor motion sensor light?
Shut Off the Power and Wire Your Motion Sensor Lights
- Shut Off the Power and Wire Your Motion Sensor Lights. The first step to installing your outdoor security lights is to shut off the power at the service panel and remove the existing floodlight. …
- Add the Motion Sensor and Restore Power. …
- Activate Your Motion Sensor.
How do you jam a motion sensor?
Fooling a motion detector is not a simple process, but it can be done.
- Learn how the motion detector works. …
- Trip the motion detector on purpose until the homeowner switches it off. …
- Reduce the amount of heat you’re giving off. …
- Introduce a masking sound. …
- Figure out the paths of the detectors. …
- Move very slowly.
Can you make a regular light a motion light?
The easiest way to turn your current porch light into a motion sensor is to switch the bulb. These bulbs are equipped with a passive infrared sensor at the top that can detect any object that produces a heat signature. As humans are constantly emitting heat, it will turn on as you enter the sensor’s range.
Do motion sensor lights work during the day?
A basic motion sensor security light will switch on at all times of the day, even at midday when the sunlight is really bright. You might not even notice that it’s switching on – if the sunlight is particularly bright, the security light could be switching on all the time.
Do motion sensors work in the dark?
Yes, motion sensors work in the dark. The way that a motion sensor detects movement has nothing to do with how light or dark it is in the immediate area. This is true whether it is a passive infrared (PIR) motion sensor or a dual-tech motion sensor that also utilizes microwave detection.
Can bugs set off motion lights?
Outdoor motion detection lights can be activated by passing cars, approaching visitors, or even rustling leaves in nearby trees. Sometimes bugs or spiders that crawl across your lights’ sensors can even trigger your lights to turn on.
