How do you attach a ledger to a house with siding?
Snap a chalk line, cut out the siding and tack up the ledger board. Then slip flashing behind the siding, covering the top edge of the ledger. Start by making an outline on the siding where you want to position the ledger board.
How do you attach a ledger board to the side of a house?
Quote from the video:
Quote from Youtube video: Code requires you to go if you're gonna when you're hanging ledgers with why this specific length. Because you want to get through both boards.
How do you flash a deck against siding?
Quote from the video:
Quote from Youtube video: Again with state line now I'm going to go ahead and show you a proper way to flash attack. We have one layer two layer three layers. The borrow fourth layer is the very top piece and the siding will
How do I attach a ledger board to vinyl siding for a pergola?
Quote from the video:
Quote from Youtube video: So you would lay out where the ledger goes and actually cut the siding. Out of the way so that the ledger can attach directly to the home. In this case you would need to use Jay metal.
Can a ledger board go over siding?
In order to install the ledger board, you usually need to remove the house’s siding. Never install a ledger board over the top of siding no matter what you hear, this can weaken the connection. Aluminum and vinyl siding can easily be removed with tin snips from an area one foot surrounding the ledger board location.
How do you attach a ledger board to a house with wood siding?
Attach-A-Deck works great for mounting a ledger over existing siding. You just drill 2 1/2 in. holes through the siding to the face of the sheathing, apply the Attach-A-Deck fasteners and mount the ledger to the house.
How many lag bolts for a ledger board?
The International Residential Code lists two fasteners for directly attaching ledgers to a house: 1/2-inch-diameter hot-dip-galvanized hex-head machine bolts and 1/2-inch-diameter hot-dip-galvanized lag screws.
How do you attach a deck to the side of a house?
Quote from the video:
Quote from Youtube video: One with the leg bolts all in place i'll just snug them. Up. Here's the second fastener that we're going to use and we're going to use it to fasten the ledger to the foundation.
How do you waterproof a ledger board?
Quote from the video:
Quote from Youtube video: It's got to be at least a 2 by 8 and then flashing. On the top. And then to cover that top edge of the metal flashing. We have the membrane once again its adhesive.
Does a ledger board need flashing?
How to Flash a Deck Ledger Board. If you cut out your siding to install a ledger board, careful steps must be taken to ensure that moisture cannot reach your house. Infiltrating rainwater can travel downward, sideways and even upward, so special flashings must be used.
Can I use 2×6 for ledger board?
Trex recommends 16″ OC at most, 12″ if running the boards diagonally. This is fine for 2×6 spacing. For the ledger, it’s worth replacing so it’s the same size. You might not be able to fully secure the larger hangers to the smaller ledger.
Can I use flashing tape on a deck ledger board?
Protect your Deck Substructure from Moisture
Applying a deck flashing tape shields the tops of joists, rim joists, ledger boards and beams from moisture. Water that penetrates the substructure through the screw holes can eventually lead to rot and decay.
Can a deck ledger board be two pieces?
The ledger board doesn’t have to be one continuous board. It can be a series of broken sections if it is solidly attached. This will require extra bolts and installing a 2x nailer across the top of the vent to secure the decking along the house wall.
How do you install flashing at the bottom of siding?
Quote from the video:
Quote from Youtube video: Begin at the windows siding that's aligned with the bottoms. And tops of windows as faster to install. And looks dope count your way down to benchmark where the starter strip will go snap.
Should decking go under siding?
Keep in mind the bottom of the upper siding should be at least two inches above the flashing or the decking that’s near the house. Never put horizontal siding in direct contact with any horizontal material.
How far should deck be from siding?
The first board you install should be about 1/8″ (3.5mm) away from the siding, to account for drainage, expansion and contraction. Predrilling is typically necessary when fastening any type of hardwood decking.
How do you install flashing between deck and house?
Quote from the video:
Quote from Youtube video: So we're doing a ledger. And the most important part of installing ledger. Right is making sure that it's long lasting it can support the deck for the duration of the decks life.
Does a deck need flashing?
“Flashing is required where exterior porches, decks, or stairs attach to a wall or floor assembly of wood frame construction.
Should you use joist tape?
In order to protect your deck’s substructure from weathering and moisture, protective tape for your joists is a must.
Can Gorilla tape be used as joist tape?
But since it was written a new product has come onto the market that is just like the concept of Gorrila tape except perfectly designed for use as a joist protection membrane. It’s called G-Tape and comes in 2″ and 4″ wide rolls.
Where do you put joist tape?
Quote from the video:
Quote from Youtube video: As we can give it a good rub. And just pull your tape all along your joist. Making sure you cover the top of it because that's where you're gonna get water down through your deck.
