Where should vanity lights be placed?

Place the vanity light bar 3 inches above the mirror for the most even illumination across your reflection. For a child’s bathroom, keep the light at the standard height, but choose a wall-hung mirror that can be adjusted.

Do bathroom vanity lights need a box?





If you’re wondering how you install a light fixture without an electrical box, the short answer is that you don’t. The electrical box, or junction box, is a code requirement that was established to prevent fires and other electrical accidents.

How much space should be between vanity light and mirror?

In those cases, when a bath bar above the mirror is the only option, vanity lights should not exceed the length of the mirror, preferably around 75 percent of the mirror’s width. Ideally, three inches should sit between the bottom of the light fixture and the top of the mirror.

How many lights should be on a 60 inch vanity?

We used 3 sconces in our 60″ double vanity with 2 recessed lights overhead. These mirrors are actually medicine cabinets that match the lower vanity.

How far from the wall should a vanity light be?

Adjust the light so that it sits over the mark you made on the wall, which should leave 3 inches between the side of the light and the side of the mirror. Use a level to determine whether the light is straight to find the final position of the light.

How high should a vanity light be installed?





It should be placed 75 to 80 inches above the floor and, like all vanity lighting, contain at least 150 watts — ideally spread over a fixture that’s at least 24 inches long so that the light will wash evenly over the hair and face.

How do you install a remodel junction box for a wall light fixture?

  1. Step 1: Trace Box. For your safety, turn off power before starting this project. …
  2. Step 2: Cut Hole. Cut the hole with a drywall saw. …
  3. Step 3: Thread Cables. Run cable through the hole. …
  4. Step 4: Insert Box. Push the box into the hole. …
  5. Step 5: Secure Box to Wall.
  6. How do you center an off center vanity light?

    Quote from the video:
    Quote from Youtube video: Here. So we know it's centered place a screw there and a screw. There. Make sure the screws are countersunk. So you can cover them up with plaster. Perfect so now we have a good backing.

    Does a junction box have to be attached to a stud?

    They don’t need to be fastened to a stud, so you can install them anywhere.

    Does the junction box have to be in the wall?

    Junction boxes must be installed where they are always accessible; never install a junction box in a concealed wall or ceiling space where the box cannot be accessed in the future. Junction boxes also must be covered with solid covers with no holes.

    How far should outlet boxes stick out?



    between 12 and 16 inches

    The common practice for receptacle outlet boxes is to install them so the bottom edge is between 12 and 16 inches above the floor.

    How do I install a light box without studs?

    Here’s how to install an electrical box without a stud using a winged remodel box:

    1. Trace the outline of the box onto the wall.
    2. Use a keyhole or drywall saw to cut out the shape.
    3. Thread the cables into the box and secure them.
    4. Push the box into the hole and ensure everything is snug how we like it!

    How do you install a remodel box?



    Quote from the video:
    Quote from Youtube video: The box and feather the opening with the edge of the utility knife until the box fits snug to install run wires into the box and position it in the hole.

    How do you install a bathroom light fixture junction box?

    Quote from the video:
    Quote from Youtube video: Once you get your hole cut make sure that your junction box fits. And make any modifications that you need hammer it in. So it's nice and tight verify that it's nice and tight.

    How do you secure an electrical box in the wall?

    Quote from the video:
    Quote from Youtube video: After your holes cut out go ahead and take your box. And slide it into the hole. Then we're going to take our drill. And tighten up these screws. Now you have a flush mounted box to your drywall.

    How do you mark an electrical box in drywall?

    Applying lipstick around the outside facing edge of a box is the perfect way to mark the location of the electrical boxes on the back side of the drywall. This way, the electrical outlets are marked as soon as you dry fit the piece of drywall in the proper place.

    Can junction boxes be behind drywall?



    Junction box covers must remain accessible; they cannot be covered with drywall or other surface material. A junction box is most often used where an electrical circuit branches off in two or more directions from a location where an outlet or fixture is not practical.