Best solution to install a sense monitor in crowded electrical panel?

  • First solution is to “piggyback” on an existing double breaker:
  • Second solution is to install a new quad breaker to group Bedroom1,2 and garage door there and have the sense use the old breaker that was used by the garage door:

Does sense need a dedicated breaker?

Sense draws less than 0.1A, so you should use the smallest 240V breaker available.

Can I install sense in a subpanel?

Yes, you can install the Sense unit in the sub panel (where your installing the breaker) and install the clamps in the main panel.

How do I install sense power monitor?

Quote from the video:
Quote from Youtube video: So remove a half-inch knockout from the panel. Slide the antenna insert onto the antenna extension cable then screw on the antenna push the antenna and the insert through the knockout.

What breaker do I need for sense?

Although the Sense monitor only draws 4W, it must be installed on a 240V breaker for device detection purposes.

Can I add sense to an existing breaker?

Add the legs for the Sense unit to the existing 240V breaker for the dryer. According to Sense, this is fine to do since the device uses less than 5 watts of power.

Can you install sense yourself?

Installation. Installation is pretty easy and you can do it yourself if you’re not scared of opening up your electrical panel to expose the primary power lines coming into your home from your utility. Power for the Sense unit can be directly tapped inside the breaker box—just be sure to cut the power before doing this.

Does Sense Home Energy Monitor Work?

Cool device and very accurate at detecting overall energy usage but individual device detection is hit & miss at best. I have had it for 3 months and it helps me monitor my overall home electricity usage in real time. It does an ok job detecting some appliances but a poor job detecting others (more on that below).

Does sense monitor voltage?

Sense measures current and voltage 1 million times per second for unprecedented accuracy. That’s about 84 million times more often than your utility’s “smart” meter.

Does sense actually work?

Sense is proven to be 99.5% accurate, compiling millions of measurements every second to provide useful, up-to-the-minute data about your home’s and appliances’ energy consumption. Sense also identifies trends by day, week, month and billing cycle to demystify nebulous electric bills and show you ways you can save.

How many outlets can be on a 15 amp breaker?

8 outlets

Technically, you can have as many outlets on a 15 amp circuit breaker as you want. However, a good rule of thumb is 1 outlet per 1.5 amps, up to 80% of the capacity of the circuit breaker. Therefore, we would suggest a maximum of 8 outlets for a 15 amp circuit.

How many circuits can be on a 15 amp breaker?

So, how many outlets exactly can you have on a 15-amp circuit? You can install a maximum of 8 electrical outlets on a single 15-amp circuit. The National Electrical Code, or NEC, limits the continuous load capacity to 80% of the rated total load of a breaker.

How many watts can I run on a 20 amp circuit?

2,400 watts

20-amp 120-volt circuit: 20 amps x 120-volts = 2,400 watts.

How do I install a subpanel to a full main panel?

Quote from the video:
Quote from Youtube video: You're going to be adding a subpanel always add the largest panel that that is practical to a door if you were thinking that you needed six circuits.

How do I increase the capacity of my electrical panel?

If you need more 15- or 20-amp breakers, a simple solution is to install a tandem breaker. The overall size of a tandem circuit breaker is the same as that of a standard breaker, but instead of a single breaker, it has two narrow side-by-side breakers.

How do I get more space in my electrical panel?

Quote from the video:
Quote from Youtube video: Похожие запросы

What is sense dedicated circuit monitoring?

Devices tracked via Flex sensor’s dedicated circuit monitoring appear along with all the other devices in the Sense app, with the ability to review historical data by day, week, month, year, or billing cycle, or set notifications for when the device turns on, off, or runs for a certain time period.

How is Sense installed?

Quote from the video:
Quote from Youtube video: Here is the connector that is for the extension of the antenna. Which you're going to use so that your sense energy monitor can connect to Wi-Fi.

How do you install a 240v circuit breaker?


  1. Turn off the Power. Open the door to the electrical service panel. …
  2. Remove Panel Knockouts. Rotate the dead front cover so you can work from the back side. …
  3. Secure and Strip the Circuit Wires. …
  4. Connect the Hot Wires. …
  5. Install the Breaker. …
  6. Check for a Proper Fit. …
  7. Connect the Wires. …
  8. Complete the Installation.

How do I add a subpanel to a full breaker box?

Quote from the video:
Quote from Youtube video: You're going to be adding a subpanel always add the largest panel that that is practical to a door if you were thinking that you needed six circuits.

How many wires can be in a 240 volt circuit?

**240Volt circuit also requires 2 wires to complete circuit. In the case of 240V, the circuit requires 2 Hot wires. One Hot wire from each ‘out of phase’ busbar is required to complete 240Volt circuit.

How many amps can 12 gauge wire handle at 240 volts?

Wire Size Selection for Long Runs

240 Volt, Conductor Size (AWG or kcmil) Single Phase, Max 3% Voltage Drop*
Copper 14 15 AMP**
Copper 12 20 AMP**
Copper 10 30 AMP**
Aluminum 8 30 AMP**

How far can you run 12 gauge wire?

You can run a 12 gauge wire up to 70 feet on a 15 amp circuit. That number drops to 50 feet if you run 12 gauge wire on a 20 amp circuit.

How far can you run #2 copper wire?

Example calcuation 2 – Copper Wire, 3 Phase power

Cable run: 400 ft. 1 conductor per phase utilizing a 750 kcmil Aluminum conductor installed Direct Buried will limit the voltage drop to 2.64% or less when supplying 194 amps for 400.0 feet on a 240 volt 3 phase system.