Basically get a nail puller, its small and managible. Get a 2×4″ or 1×4″ block, or a 1×1″ and cut a slot in it so that you can fit it right over the existing wire. Then use the block as your pivot point for the pry bar to work against. Cut new blocks as needed for awkward locations.
How do you remove metal Romex staples?
Quote from the video:
Quote from Youtube video: You use one nifty technique. I have here my side cutters there's my standard side cutters. And what I want to do is grab the edge. Just behind the wire here and then gonna squeeze pretty hard.
How do you remove stapled wires?
Quote from the video:
Quote from Youtube video: But you just grab the edge of the metal. And you push down. And then you just slowly work out the staple. Now just like a hammer. If you need more leverage you can put a piece of wood down underneath.
How often should NM cable be stapled?
Runs of NM cable must be supported at least every 54 inches. 1 They also must be secured within 12 inches of an electrical box that includes a cable clamp or within eight inches of a box or enclosure without a cable clamp.
What happens if I staple through a wire?
Wrong kind of staples. Eventually they might all abrade the cable, whether or not you stapled right through it and present a fire hazard. Replacing the cable would be best. Inspecting the damage would be good, but then you’d have a splice to deal with or have to re-insulate, both having to be waterproof.
How do you remove construction staples?
Quote from the video:
Quote from Youtube video: And just pry up the staple easily the only force you need to put on the pliers is a tiny bit to keep them in contact with a staple. If you are gonna use the 90 degree bit needlenose.
How do you remove staples from a wall without a staple remover?
Flathead screwdriver and pliers make a good tandem if you want to go primitive. You can use the screwdriver to pry up or separate the screws and the pliers to pull them loose. If you’d rather, you can just go for the pliers. Office-style staple removers can be effective at removing certain varieties of staples.
Can you use metal staples on Romex?
Most metal and plastic staples or ‘wire holders’ can hold stacks of up to six to eight (6 to 8) Romex wires under them. You can stack even more if you can fit them or use thinner wires. However, it is not permitted by code to stack more than one 3-conductor cable under a staple, be it metal or plastic.
How do you staple a Romex cable?
Quote from the video:
Quote from Youtube video: About is not stapling romex on edge these are flat cables. So you need to put the cables down flat on top of each other and staple on top of that.
How do you fish wire?
Quote from the video:
Quote from Youtube video: Directly below the box feed your fish tape into the wall opening. Pushing it up into the hole you made in the topically. If you're running cable through a basement or crawlspace. Push.
How many nm cables go through a hole?
The Answer. According to the National Electrical Code, you can have 4 12/2 nonmetallic sheathed cables through a single bored hole that is fire- or draft-stopped using thermal insulation, caulk, or sealing foam, or where proper spacing is not maintained for more that 24 in.
Why did Romex wire go up in price?
These price increases are due to factors such as China’s economic recovery from the pandemic, sustainable green energy stimuluses, and supply disruptions. China’s rising industrial production along with aggressive sustainable energy initiatives accredits the country to being the highest consumer of copper in the world.
How tight should Romex staples be?
Do not hammer in those cable staples too tight. They should be just enough to hold the cable in place, but not so tight as to pinch the cable. It may not look like the staple is damaging the conductors, and the problem may not present itself for a few years after installation, as was the case here.
How do you remove wire fence staples?
Quote from the video:
Quote from Youtube video: Like this on it that is the cat's meow for pulling fencing staples all you're gonna do is hook the staple like so between the pinchers and pry down on it like this and I'll rip it right out.
How do you use heavy duty staple remover?
Quote from the video:
Quote from Youtube video: And then you gently push it down while it pulls the staple up it's very simple and easy to use i'm going to show you a close-up right now all you need to do is slip it in under the staple.
How do you remove staples from a big stapler?
Quote from the video:
Quote from Youtube video: So when you go to pull this out like we all have you grab it you twist it you pull it it sticks of course you can have special tools to be able to do it.