If the LEDs will not light up at all, then this could be down to a faulty power supply. If you have several power supplies, then try a different power supply onto the same strip to see if this now works. If it does, then you have a faulty power supply and will need a new one.

Why are two of my LED lights not working?

Bad Pin Connection – If your LED strip light fails to turn on at all, then check your pin connections. Most likely, the pin is not inserted correctly. In rare cases, the pin is faulty. These tiny connectors are rather delicate items so you have to be very careful when inserting them.

Why wont all of my LED lights turn on?





Heat buildup, screwing bulbs too tightly, or placing LEDs in improper electrical circuits and accessories are common causes of LEDs stopping working. In addition, poor quality capacitors, drivers and diodes are also leading factors in reducing the life of LED bulbs.

How do you get both LED lights to work?

Quote from the video:
Quote from Youtube video: Just here you can chop off the little ND bit and then slot it into place spot the other one into place. Job.

How do I reset my LED light that won’t turn on?

To reset the light strip, locate the corded controller which is attached to the power supply of the light strip. Insert a paper clip, or a similar sized object, into the reset hole on the controller (depicted below). Using the paper clip, press and hold the reset button inside the reset hole for eight (8) seconds.

Do LED lights burn out?

LED lights cannot burn out because there is no use of heat as in incandescent bulbs, or gases to burn out or wires to burn up. The microchip inside the LED produces a small amount of heat, which is taken away by the heat sink, meaning that no parts in the bulb are designed to burn up.

Can LED lights be repaired?





A great benefit to LED bulbs is you can repair almost everything. Premature burnouts can be caused by poor component quality, LED overheating, and voltage jumps. The good news is that you don’t have to have a lot of experience to handle the repair and the cost is significantly less than the price of a new bulb.

How do you fix LED lights?

Quote from the video:
Quote from Youtube video: That have had dry solder joints. But in this video. I'm going to show you how to use these now this is a 12-minute RGB W tape to tape connector.

How do you reset LED lights yourself?

Quote from the video:
Quote from Youtube video: This is exactly first of all you push all these all the way down. And then make sure that it's pointing to your LEDs. Though. So if it's not going to stop there your LEDs.

Does any remote work for LED lights?

It is possible to connect an LED light strip to more than one remote. You simply need to sync the strip to both remotes. Controllers usually remember an LED light strip’s last settings. If you are using multiple remotes to control a strip, the remote you used last will decide on the LEDs’ settings.

How do I control my LED with my phone?



Quote from the video:
Quote from Youtube video: You to type in your Wi-Fi. Password into the into. This app I think so yeah it's pretty simple to set everything up and once it's connected you can use a multiple devices.

How do I turn on my LED lights without the remote?

To turn on LED lights without a remote, you need to manipulate their power source. Plugging it in and out is the easiest way. Another way is to control the LED lights through an app. Using smart switches can also be a long-term fix.

Can I control my LED lights with my phone?

You can remotely control your led tape lights by your smartphone APP. You can also easily change brightness, color, mode, speed and as much as 16 colors.

Can you cut day better LED lights?



Daybetter LED strip lights can be cut along the cutting marks. Their circuits are closed between each cutting point, meaning that as long as you don’t cut outside it, you can snip them into any size you need. The Daybetter brand has strong 3M glue compared to some other brands.

Why is my LED remote not working?

If your remote control suddenly stops working or your lights start blinking, you may need to reset the controller and pair it back to the receiver unit. The controller sometimes un-pairs itself from the receiver due to a loose connection, radio interference from an external source or a low battery in your remote.