How do you loosen a stuck brass pipe fitting?

Quote from the video:
Quote from Youtube video: Fitting use a regular propane or map gas torch to get it nice and hot. And then take the joint apart while it's still heated. That will make it a lot easier since the fitting expands.

How do you remove a bathtub overflow cap?





To remove it, place your thumbs at the bottom of the cover plate and press gently upward until the plate snaps free of the underlying mount and pops off in your hand. Depending upon whether you’re troubleshooting, cleaning or upgrading, you can snap the same cover plate or a new one over the same mount.

How do you remove an overflow cover?

Quote from the video:
Quote from Youtube video: In some cases you may only have one screw but all you need to do is remove. The screws and as you can see. The cover is removed.

How do you remove a bathroom overflow?

Quote from the video:
Quote from Youtube video: Sorry there's actually a Philips screw just on the side of the unit. So you want to get in a screwdriver a Phillips one or a flathead. And just open that screw up.

How do you extract brass fittings?

Quote from the video:
Quote from Youtube video: It's that simple and simply to get these off you would go clockwise. And they'll loosen themselves and there you go guys.

How do you loosen old pipe fittings?





Quote from the video:
Quote from Youtube video: And it's very hard a little elbow grease maybe a little heat. And some penetrating oil and be careful because the penetrating oil is highly combustible.

How do you remove a bathtub drain that has no screws?

Quote from the video:
Quote from Youtube video: You just kind of lift it up twist it a bit there's no grooves in there there's no screws.

How do you remove rusted overflow drain screws?

You can try inserting a hacksaw blade into the drain opening, then press it up against the screws that are on the back of the drain cap. Saw slowly and carefully to avoid scratching the tub. Alternatively, try to chisel and chip out some wood that is around the screw head.

How do you remove a bathtub drain cover without screws?

Quote from the video:
Quote from Youtube video: One get yourself some wd-40 spray it around the rim of the drain. Let it sit for about 15 minutes or so and then get yourself some pliers that fit into these holes in the drain.

How do you remove a bathtub waste pipe?



Quote from the video:
Quote from Youtube video: Turn my drain assembly and that will remove it from the waste tissue which is below the tub. And. I can put a screwdriver in the hole in the drain. Tool as well. Once. I get it loose.

Can you replace the overflow in a bathtub?

If the main waste-water drain is functioning properly and in good condition, you can replace just the overflow drain. This is a task that most homeowners can do themselves, without a pricey visit from the plumber.

How do you unstick a bathtub plug?

Lift and Turn Tub Stopper



With the stopper in the open position, use one hand to hold the body of the stopper in place. Slowing turn the knob counter-clockwise, looking for a screw set on the knob. If there isn’t one, turn the stopper counter-clockwise to unthread from the strainer until it can be removed.

How do you unscrew a threaded pipe?



Quote from the video:
Quote from Youtube video: Hold it in one hand and twist the tool clockwise with the wrench. And it should just loosen. So that's it next time you have a stuck pipe nipple try using an internal pipe wrench tool to remove it.

How do you remove compression fittings from brass?

Quote from the video:
Quote from Youtube video: And place the forks of the puller behind the compression ring and nut. Next turn the puller handle clockwise until the compression ring and nutter pulled loose from the copper.

How do you remove a stuck brass bolt?

Quote from the video:
Quote from Youtube video: Use a 6-sided wrench or socket. If the bolt still won't break free consider using a tool extender to added torque just be careful not to break off the head of the bolt.

Does wd40 loosen bolts?

If the bolt is stuck in place because of rust, you can use a bolt loosening spray such as WD-40 Penetrant Spray. This penetrating oil provides deep lubrication to loosen the nut or screw.

How do I unscrew metal from metal?



Quote from the video:
Quote from Youtube video: So you can pull this in and get a good firm grip around what you're trying to pick you know pull off and then turn your big screw down and it'll pull it right up off of the shaft.

Why does heating a bolt help remove it?

If you’re talking about a nut on a bolt, heating the nut more than the bolt will cause the nut to enlarge relative to the bolt. This action is simple and straight-forward — you should simply take care to concentrate the heat on the nut, not the bolt.

How do you loosen a stuck bolt on heat?

For stubborn bolts, heat the bolt, then move the flame away and apply WD-40 against the heated bolt threads. The melting wax pulls itself into the threads to create a slippery surface. Keep open flames away from fuel and brake lines, rubber fittings and other flammable parts and materials.

How do you remove a heated seized bolt?

Torch Your Stuck Bolt



Using a flame to loosen the bolt. Now heat the bolt and nut. Put the flame directly over the stuck part, or the part you can get to safely. Heat it for 30 seconds or so and it should free up easily.