Yes you can

Does a 60 amp sub panel need a main breaker?

Your subpanel does not need a main breaker if it’s in the same building. If it is in an outbuilding, you need a disconnect switch, and the breaker will suffice but its size doen’t matter.

How do you install a 60 amp sub panel?






Quote from Youtube video: Goes to the ground or goes through the neutral wire they both ends up in the same place here at the main box. This is actually unbonded at the at the sub panel box we'll get to that in a second.

How far can a sub panel be from the main panel?

Installing a Subpanel and Choosing Cable



You must provide from 3 to 4 feet of clearance on all sides of the panel depending on the voltage to ground. You may not know this voltage, so it’s best to provide 4 feet.

What wire do I need for a 60 amp subpanel?

It is common to wire 60-amp breakers with 6-gauge, 3-conductor wire because an appliance that needs a 60-amp breaker rarely draws the full 60 Amp. It’s a good idea to connect a 60-amp subpanel to the main panel with 4-gauge wire.

What is the 6 breaker rule?

The “rule of six” refers to how many breakers or throws it takes to disconnect a building from the electrical supply, so if you have more than six breakers in a box at your service entrance there needs to be a disconnect upstream of it, either in the panel or upstream.

Can a 60 amp breaker feed a 100 amp sub panel?





You can feed a 100 Amp panel with a 60 Amp breaker. Keep in mind that the sub panel needs to be rated above the breaker size.

Can I add a 60 amp breaker to my panel?

However, if you only have a 60-Amp service panel and want to add a new 60-Amp subpanel, you’ll have to upgrade the main panel to allow such an addition. Most modern homes use a 200 Amp panel. Depending on your electrical panel, you might not have the available capacity to add a 60-Amp breaker.

How many breakers can I put in a 60 amp subpanel?

The minimum amperage panel for modern homes is 100, 150, or 200-amps. The NEC does not allow installing panels rated below 100-amps as the main electrical panel for the house. Modern 60-amp electrical panels are purpose-built as sub-panels and generally only have 8 to 10 slots available for circuit breakers.

What size wire do I need to run 60 amps 100 feet?

4 AWG



What size wire should I use for a 60 amp subpanel? You can get away with 6 AWG when you have a short run of wire, however, due to voltage drop, if you ever decide you want to go more than 100 feet then a 4 AWG is the size you should choose.

Can 6-gauge wire handle 60 amps?

6 AWG can only handle 65 amps. Here’s what a professional will know: The next wire size that can handle more than 75 amps (as required for a 60 amp breaker) is the 4 AWG gauge wire. 4 AWG can handle 85 amps; that’s more than enough ampacity to adequately wire a 60 amp breaker, even accounting for the 80% breaker rule.

Will 6-gauge wire carry 60 amps?

The common practice is to assign 6-gauge wires to 60-amp circuits and appliances. However, I’m convinced that a 4-gauge wire is far superior. Precluding the cost consideration, there is no downside to using wires of much greater size for your 60-Amp circuit.

Can 8 gauge wire handle 60 amps?



“Twelve-gauge wire is good for 20 amps, 10-gauge wire is good for 30 amps, 8-gauge is good for 40 amps, and 6-gauge is good for 55 amps,” and “The circuit breaker or fuse is always sized to protect the conductor [wire].”

What size cable do I need for 60 amps?

6 AWG to 4 AWG

For 60 ampere breakers, electricians and professionals suggest using a wire size gauge ranging from 6 AWG to 4 AWG. All household wires have a rating of at least 600V, so only amperage really matters when it comes to determining wire gauge. Therefore, the wire size for 60 amp 220v, for example, is still 6 to 4 AWG.

How many amps is #6 wire good for?

Size & AMP Ratings

NM, TW, & UF WIRE (Copper Conductor) SE CABLE (Copper Conductor)
12 AWG – 20 AMPS 6 AWG – 65 AMPS
10 AWG – 30 AMPS 4 AWG – 85 AMPS
8 AWG – 40 AMPS 2 AWG – 115 AMPS
6 AWG – 55 AMPS 1 AWG – 130 AMPS

How many watts can a 60 amp breaker handle?



The amount of power that each circuit can handle is the number of volts (usually 120) times the number of amps. Therefore, that 60 amp circuit can handle 7200 watts.

What do you use a 60 amp breaker for?

The Square D by Schneider Electric Homeline 60 Amp Two-Pole Circuit Breaker is used for overload and short-circuit protection. Homeline load centers are compatible with this breaker.

How much does it cost to upgrade from 60 amps to 100 amps?

To upgrade to 200 amps, expect to spend $1,300 to $2,500, or $2,000 to $4,000 to upgrade to 400 amps. A low-amp subpanel costs $500 to $1,000.



Cost to Replace or Upgrade an Electrical Panel.

Amps Average Cost
Upgrade from 60 to 100 Amps $850 – $1,100
Upgrade from Amps $1,300 – $1,600

Can I use a 60 amp breaker for a 50 amp stove?

Most 240-volt electric stoves require a 50 amp double-pole circuit breaker with a #8 gauge copper wire or #6 gauge aluminum wire. Some industrial electric stoves need a 60 amp breaker, while older ones can get away with 30 amp breakers.

Is 10 3 wire heavy enough for a stove?



A typical electric dryer, and most combined stackable units, will require a 30A-120/240V circuit using 10/3 cable. Show activity on this post. This chart indicates that for a common household electric stove/oven at 240V, up to 30A, a 10/3 wire is proper.

How many amps does a dryer pull?

Residential electric clothes dryers use between 7.5 amps and 30 amps. However, 30 amps is by far the most common. The National Electrical Code (NEC) standards require that 240V dryers have a dedicated 4-wire circuit (10-3 type NM cable with ground) protected by a 30 amp breaker.