https://youtu.be/TSNAJ8xCtro
What size SharkBite do I need for 1/2 inch copper pipe?
Pipe Insertion Depth Chart
| SharkBite Fitting Size | Nominal Pipe Size | Pipe Insertion Depth (in.) |
|---|---|---|
| 1/2 in. | 1/2 in. CTS | 0.95 |
| 5/8 in. | 5/8 in. CTS | 1.13 |
| 3/4 in. | 3/4 in. CTS | 1.10 |
| 1 in. | 1 in. CTS | 1.31 |
How do you cut copper pipe for SharkBite?
Quote from the video:
Quote from Youtube video: Tool to cut out that damaged piece of copper pipe this is why we love the autocut. Tool it only takes a few seconds to do that then deburr the outside edge of the copper pipe with the sharkbite.
Can you use SharkBite on soft copper?
Can SharkBite fittings be used with soft copper or rolled copper? No. SharkBite fittings can only be used with hard drawn copper types K, L, and M.
How do you install a shut off valve on a copper pipe?
Quote from the video:
Quote from Youtube video: Put the ferrule over the top. As. Well make sure it goes down all the way it can't be partially down it has to be all the way down so it slides down the pipe. So that way we can slide the valve.
Should I sand copper pipe before SharkBite?
Do not sand the copper pipe – while it’s the easiest way to smooth out the edge of the pipe, this practice should be avoided whenever possible since it disrupts the otherwise even pipe surface and may compromise the seal.
How do you use a 1/2 inch SharkBite?
Quote from the video:
Quote from Youtube video: To use the disconnect clip snap it onto the pipe press the release color using the disconnect clip and pull the pipe from the fitting.
How do you install SharkBite fittings on old copper pipe?
Quote from the video:
Quote from Youtube video: If you get back near an old fitting there'll be significant slag from the solder joint. And it's not going to seal around that it really needs a smooth radius around the outer diameter.
How reliable are SharkBite fittings on copper pipe?
SharkBites work better than plastic quick-connects on copper pipes because the lead-free brass body is rigid like the pipe and has a higher pressure tolerance. If you need to repair or replace copper plumbing in your home, a SharkBite fitting is an excellent choice.
How long do SharkBite fittings last on copper pipe?
SharkBite fittings last a long time. In fact, SharkBite warrants the fittings for 25 years when used with SharkBite tubing.
Can a sharkbite valve be used for main water shut off?
Shark bite valve will be fine. Just make sure you clean the copper pipe thoroughly so there are no rough edges or bits of solder left.
How do you attach a valve to a copper stub?
Quote from the video:
Quote from Youtube video: Using a torch heat the joint until solder liquefies. And feed solder fully around the edges of the valve. When soldering is complete wipe the connection with a damp cloth.
How do you install a shut off valve on a PEX pipe?
Quote from the video:
Quote from Youtube video: So the first thing you need to know is do you need a straight or an angle. And then what size okay typically the pipe that you're going to be changing this out from will be a half inch pex.
Are shark bites as good as solder?
These groups of home owners feel SharkBite fittings are just as strong as soldering. A few of the criticisms of SharkBite and other push-fit fittings consist of; initially, push-fit fittings do not have the trustworthiness that soldering has. Soldering has actually been around much longer than push-fit fittings.
How do you stop a SharkBite from spinning?
Show activity on this post. Silicone tape along the base of the SharkBite valve should keep it from rotating on the pipe. Make sure the silicone tape overlaps itself (that’s how it sticks). Make sure you allow enough time for the tape to fuse to itself as well.
How do you stop a SharkBite from leaking?
Quote from the video:
Quote from Youtube video: Product you can remove the paint near the end of the pipe where the fitting will be located. Once the paint has been removed you can reconnect the fitting.
Do professional plumbers use SharkBite?
When and when not to use SharkBite fittings. Most professional plumbers believe that SharkBite fittings and other kinds of push-fit fittings should only be used as an emergency, temporary fix, and not for any enclosed or permanent plumbing system. However, there is a growing selection of DIYers who would disagree.
Do you use Teflon tape with SharkBite?
Teflon tape should be used with threaded SharkBite connectors to make a proper seal. SharkBite Universal fittings should not be installed (threaded or push-to-connect) on galvanized tubing.
Do SharkBite fittings leak over time?
Once they clamp down, these fittings create a tight, waterproof seal. However, if your SharkBite fittings are leaking, then you know that there’s a problem that should be fixed as soon as possible.
Do shark bites work on black pipe?
If you need a way to quickly transition to PEX, Copper, C-PVC, PE-RT, or HDPE pipe, we have you covered. The SharkBite fitting can change from one pipe material to another. Polybutylene pipe is compatible with SharkBite fittings with a gray collar.
