Since LED lights work on low DC voltage, they need a driver. Most T8 LED tubes do not need a ballast. So, if you are going to install a T8 LED tube light, it will require a ballast bypass unless you choose a ballast compatible T8 LED tube.

Do I need to remove ballast for LED tube?

An LED light does not require a ballast because it uses a component called a “driver” to regulate the power going into the bulb.

Can you put LED bulbs in fluorescent ballast?





In short, YES!



New linear LED tube bulbs are simple plug and play and ballast compatible. You will simply need to remove your fluorescent bulb and plug in your LED replacement.

Do I need to change the ballast for LED lights?

Unlike fluorescent tubes, LEDs don’t require a ballast to regulate current. When using direct fit LEDs, the ballast is still using energy and eating into your possible energy savings. With a ballast bypass, you are only paying for the energy the LED lights use, which is up to 70% less than traditional bulbs!

Can LED tube work with ballast?

The only type of LED tube that requires a ballast is plug-and-play. Used as direct replacements for fluorescent tubes, plug-and-play LED tube lights install without fixture rewiring, and operate off the existing fluorescent ballast. Hybrid LED tubes can be used with a ballast, but one is not required.

Can I replace a fluorescent tube with an LED tube?

Answer: Great question – and the answer is yes, an LED tube light can be installed in a traditional fluorescent tube light fixture, without the ballast.

Can you put LED bulbs in old fluorescent fixtures?





You have fluorescent tube lights in your home or business already, and you’re wondering if you can pop LED tubes in these fixtures or if you’ll need to change out the fixtures for something designed for LED. Good news! You can use LED tubes in your existing fixtures!

Can you mix LED and fluorescent tubes?

Yes, you can mix LED lights with other types of light bulbs. The most important thing is to make sure all of your fixtures are the same type.

Can I use LED bulbs in any fixture?

As long as the mounting base (socket) is the same size and type, you can use an LED bulb in an existing fixture. If the mounting base isn’t the same size and type, the LED bulb will not fit the socket. You should never use a bulb with a higher wattage than what is recommended for the fixture.

Can you replace T12 fluorescent tubes with LED tubes?

T8 LED tubes won’t fall out if you try to install them in a T12 fixture—they’ll fit just fine. But here’s some even better news: If you have a T12 fixture, conversion to LED is going to be even easier than with a T8 fixture. This is because T12 fixtures have non-shunted tombstones, exactly what you need for LED tubes.

How do you bypass a ballast to install LED tubes UK?



Quote from the video:
Quote from Youtube video: We'll need to jump the power from one tombstone to the next install the wires into the tombstone. And install the tombstones on the bracket install incoming power supply into the tombstones.

Is ballast bypass safe?

Safety risk



The most significant negative to a ballast-bypass linear LED is the risk of electric shock since the sockets carry line voltage. It’s a common practice to place a finger on the lamp pins while you are trying to install it, and this becomes a risky endeavor when using single-ended ballast-bypass lamps .

Can I replace fluorescent tubes with LED tubes UK?

In simple terms if you have a fluorescent tube fitting with an old fashioned starter you can simply remove the starter and then short circuit the connections across the inductive ballast. This will take the inductive ballast out of the circuit and mean that you have mains voltage applied to either end of the LED tube.

How do I wire a ballast free LED bulb?



How to Bypass a Ballast

  1. Turn off the power. Flipping the light switch to the “off” position does not necessarily end the flow of electricity. …
  2. Locate your ballast. …
  3. Cut the hot and neutral wires. …
  4. Cut the socket lead wires. …
  5. Remove the ballast. …
  6. Connect the input wires to the output wires.


How do you install LED tube light fixtures?

Install LED tubes in a fixture with conventional ballast

  1. Remove the fluorescent tube.
  2. Remove the starter.
  3. Insert the LED starter.
  4. Insert the new LED tube.


How do you wire a direct wire LED tube?



Direct-Wire

  1. Turn off the power source.
  2. Remove the fluorescent tube.
  3. Cut the wires leading to the ballast.
  4. Remove the ballast.
  5. Install new lampholders (tombstones) that create a direct connection to the line voltage.
  6. Cap any loose wires.
  7. Install new Energy Focus LED tube.
  8. Turn on the power source.


How do you rewire a LED fluorescent light fixture?

Quote from the video:
Quote from Youtube video: The other way that we do this and they come double ended where the black wire goes on one end and the white wire goes on the other end.

How do you bypass the ballast for LED lights?

How to Bypass A Ballast

  1. Step 1: Disconnect All Power So There is No Electrical Current. …
  2. Step 2: Find the Ballast. …
  3. Step 3: Locate and Cut Only the Hot and Neutral Wires. …
  4. Step 4: Cut the Socket Lead Wires. …
  5. Step 5: Remove the Ballast (if you wish) …
  6. Step 6: Connect the Wires. …
  7. Step 7: Reattach Any Coverings and Turn On.



How do I know if my LED tube is single or double ended?

A simple way to know if you have a single ended tube is to look for the L/N or AC INPUT sticker at the end of the tube. Since the single-end powered tubes only use one side of the tube, both live and neutral power will be on the same side, but different pins. The “L” indicates the pin that live power will go into.