It is possible. If the tube is old and brittle than you may crack it. If you do crack the tube, or you have to cut it, you can buy new inexpensive tubing and barbed couplers as well. Heat it up with a hair dryer or hot water and slowly wiggle it back and forth as you pull.

How do you remove barbed drip irrigation fittings?

Quote from the video:
Quote from Youtube video: In just get in here with your pliers. And then you twist it and it'll help clap it. And you can pop that piece right out.

How do you remove a barbed connector?





Quote from the video:
Quote from Youtube video: There's two ways you can do it actually one way is to take utility knife. And make a slight. Ever so gently cut in it. And comes off that easy.

Can you reuse drip compression fittings?

Quote from the video:
Quote from Youtube video: Okay we're going to show you how to reuse these push aunty fittings I use these all the time and they're great. But if you want to move line to one other part of the yard.

How do you remove a hose barb hose?

Quote from the video:
Quote from Youtube video: The old way of doing it was to use a knife and cut the holes like this and as you're doing this it wrecks the bar. You can see here by using a knife you're gonna score up the bar.

How do you install barbed fittings?

Quote from the video:
Quote from Youtube video: They're really easy to use the great thing about it is is you just take the bitting take your tubing. And push it in sometimes this is a little easier than other times.

Do barbed fittings need clamps?





For highly inflexible tubing, clamps are often necessary. Tubing that has been repeatedly installed and removed over one or more barbs and is no longer elastic enough to relax behind a barb will require a clamp, too.

How do you remove a push on hose connector?

Quote from the video:
Quote from Youtube video: We press in both the hose and the collar. We hold the collar and pull to remove the hose. If we need to reinstall this hose. We want to cut past where our notches are from where the collar.

How do you remove a hose fitting?

Quote from the video:
Quote from Youtube video: And there's a couple other methods I'll show you how to do as well. Sometimes a pair of pliers just kind of moving it back and forth. You'll actually feel the hose snap.

How do you remove a braided hose fitting?

Quote from the video:
Quote from Youtube video: So let's start again there keep these in your heads. This is the a in this part you don't touch. This part is the hose end it screws on to that this end is what goes on to the hose.

What is a barbed connector?



A barb connector or hose barb is the section of a fitting or component connected to a piece of hose or tubing by being inserted into that hose or tubing.

How do you use a barb connector?

Stick the tip of the barbed fitting into the open end of the tubing that you just heated up. Wiggle the fitting using back and forth and up and down motions, while simultaneously pushing hard, until it’s all the way inside the tubing.

How do you fit a hose to a barbed fitting?

Quote from the video:
Quote from Youtube video: Much easier push the hose onto the fitting. Until the hose bottoms out on the fitting hex or stop ring align the clamp over the hose barb tighten with a screwdriver arno hub coupling wrench.

What size hose fits a 1/2 Barb?



Nominal Millimeter: Best practice conversion of inch-based fittings onto metric-based beverage tubing, e.g. 1/2″ barb fittings can be used on 13.5 mm OD beverage tubing.

Where do hose clamps go on barbed fitting?

Quote from the video:
Quote from Youtube video: Along one edge.

How do you install barbed fittings on a poly pipe?

Quote from the video:
Quote from Youtube video: Move the hose clamp over the poly pipe and poly pipe fitting tighten the hose clamp to the point of resistance. But do not over tighten. Over tightening hose clamps can cause cracking in the poly.

Can I use barbed fittings with PEX?

Quote from the video:
Quote from Youtube video: And can connect to PEX orpurt pipe both fitting options can be connected with either copper crimp rings or stainless steel clamp rings.