It is a safety switch designed to prevent the drum from turning while the door is open. If the switch were removed and the circuit closed by connecting the wires the drum will turn and the dryer will work. Can you get someone to tell you it is an okay thing to do, not likely.

How can I bypass a dryer door switch?

Quote from the video:
Quote from Youtube video: Use a flat screwdriver like these to open the top panel then lean the panel against the wall. Use the edge of a party knife to disengage the switch from the harness.

How do you fix a broken door switch on a dryer?

Quote from the video:
Quote from Youtube video: Use a slot screwdriver to release the locking tab on the wire harness plug for the door switch remove the mounting screws from the existing door switch. Pull the door switch out of the dryer.

Can you bypass dryer door switch on GE dryer?

Quote from the video:
Quote from Youtube video: This is the jumper wire we're gonna use to bypass the door switch connect the jumper wire to the two wires of the door switch. Like this use electrical tape to insulate the connections.

How do I know if my dryer door switch is broken?

Quote from the video:
Quote from Youtube video: No continuity means the electrical path is broken and the switch has failed switches come in many shapes and sizes. But all of them can be tested for continuity in the same.

How do you test a dryer door switch?

Quote from the video:
Quote from Youtube video: Go to normally open so when the dryer doors. Open the motor is not going to be able to get power but when you close the door.

How do you bypass a thermal fuse on a dryer?

Locate and Bypass the Fuse

The thermal fuse will look like a thin strip of white plastic with a wire coming out of each end. In order to bypass the thermal fuse, use electrical tape to tape the two ends together. The thermal fuse will then be bypassed. Turn the dryer on to a heat cycle for no more than 90 seconds.

How much does it cost to replace a dryer door switch?

Cost to Replace a Dryer Door Switch

Replacing a door switch averages $50 to $150. The door switch is a small and cheap component, but it is very important because it detects when the door is closed or open to prevent the dryer from running with an open door.

When I press the start button on my dryer nothing happens?

If the dryer start switch does not have continuity when it is activated, it will need to be replaced. The door switch is located near the dryer door and is activated when the door is closed. If the door switch fails, the dryer won’t start at all. Most door switches will make an audible click when they are activated.

Why doesn’t my dryer shut off when I open the door?

If the dryer stops only when you open the door, you’ll likely need to replace the electronic control board. If the dryer won’t turn off when you open the dryer door, the dryer door switch likely failed. Replace the door switch if it doesn’t accurately detect the door being open or closed.

What would make my dryer not turn on?

Common dryer issues include a faulty door switch or start switch and control problems such as a broken dryer timer or faulty electronic control board: Problems with the door switch can prevent the dryer from starting.

How does the dryer door switch work?

A door switch is a simple on/off mechanism that prohibits the dryer from operating when the door is open. Dryer door switches are a little over an inch long. Many are white in color and all have metal prongs, called terminals, extending out from the body of the switch.

What does dryer interlock switch do?

Related Articles. A dryer door relay is actually a switch that completes a circuit when the door closes. The purpose of the door switch is to prevent the dryer from running while the door is open. These switches typically last a long time, but they can fail before the dryer does.

Why does my dryer keep running when the door is open?

However, if your dryer is spinning with the door open, your problem is probably the dryer door switch. This switch is a common safety feature found on all dryers, especially modern ones. It keeps the drum from spinning once the door opens. To test if your switch is faulty, use a multimeter tool to test for continuity.

How do you remove a dryer switch?


  1. Shut off the power. Unplug the dryer. …
  2. Remove the lint screen. Pull the lint screen out of the housing in the top panel of the dryer. …
  3. Remove the lint screen housing screws. …
  4. Raise the top panel. …
  5. Disconnect the door switch wire harness. …
  6. Remove the door switch. …
  7. Install the new door switch. …
  8. Connect the wire harness.

How do you change a start switch on a dryer?


  1. Shut off the power. Unplug the dryer. …
  2. Pull the knob off. Pull the control knob straight up and off of the front of the push-to-start switch. …
  3. Remove the back panel. …
  4. Remove the push-to-start switch. …
  5. Install the new push-to-start switch. …
  6. Reattach the back panel. …
  7. Reinstall the control knob. …
  8. Restore power to the dryer.

How do you fix the start button on a Whirlpool dryer?

Quote from the video:
Quote from Youtube video: Pull the tab and rotate the old switch to release disconnect the wires. You're now ready to install the new start switch reattach the wires.

How do I replace a door switch?

Quote from the video:
Quote from Youtube video: As you remove the last screw. You want to hold the switch in your other hand. So that it doesn't fall down inside of the sight. Then pull it out through the back.

How do you replace the door switch on a Whirlpool dryer?

Open up the dryer door and remove the two screws that hold the door switch in place. Pull the switch out and set it aside. To reinstall the new switch, slide it into the now empty square opening and line-up the screw holes. To securely attach the new door switch, reinsert the two screws you previously removed.

How do you change the door switch on a Whirlpool Duet dryer?

Quote from the video:
Quote from Youtube video: Open the dryer door and use a Phillips head screwdriver to unthread the screws securing the front panel to the bulkhead. Using the quarter inch socket or nut driver unthread the upper mounting.