Yes. This is a fairly common practice.
How much should a sill plate overhang?
Consult with engineered lumber providers to get acceptable installations. Notes: 1. Sill plate overhang limited to ½ the nominal thickness when rim joist is resting on outer edge.
How do you fill gap between sill plate and foundation?
Caulk and, or spray foam can be applied at the seam where the sill plate sits on the foundation, and it can be used to seal (and insulate when spray foam is used) the area where the subfloor and rim joist sit on the sill plate.
What is the material called that is placed between the foundation and the sill plate?
Terms in this set (58) Why is sill sealer is used between foundation wall and sill plate? Designed to REDUCE AIR LEAKAGE between the foundation wall and sill plate. The Sill Sealer can also be used to seal around window and door frames.
How are sill plates attached to the foundation walls?
One method for fastening sill plates is the use of cast-in-place anchors, commonly referred to as “J” Bolts. “J” bolts are anchors in the shape of the letter J with threads on the end opposite of the bent end. These bolts are set in place before the concrete is poured.
Can a sill plate overhang foundation?
Two inches of sill plate overhang is quite a bit. However, in years past sill plates were often built with 2x4s. I assume the builder is using 2×6 or 2×8 pressure treated sill plates, so I suspect you have at least 3.5 inches of sill plate material on the top surface of the foundation wall.
Should sill plate be flushed foundation?
Sills can be placed flush with the foundation wall, set back slightly, or even overhang slightly depending on the exterior surface material (check local codes for the amount of overhang allowed).
What should I put between wood and concrete?
Anyplace where wood meets the ground or concrete, the lumber must be pressure treated. For additional moisture protection, a gasket or strip of closed-cell foam can be installed between the concrete foundation and the sill plate.
How do you fill gap between foundation and wall?
The gap between slab and foundation is an in-built design unless the gap is larger than 0.4 inches. If that’s the case, you can seal the gap between the concrete and wall using a concrete caulk. Or by taping the gap using window seal tapes. But make sure to seal it before it cracks up even more.
How do I fill a large gap in my foundation?
Youtube quote:So you're going to take your backer rod pack. It in there to bring it closer to the surface.
How thick should a sill plate be?
1 Bottom Plates. Studs shall have full bearing on a 2-inch-thick (actual 11/2-inch, 38 mm) or larger plate or sill having a width not less than equal to the width of the studs.
What is the difference between a sole plate and a sill plate?
A sill plate or sole plate in construction and architecture is the bottom horizontal member of a wall or building to which vertical members are attached. The word “plate” is typically omitted in America and carpenters speak simply of the “sill”. Other names are ground plate, ground sill, groundsel, and midnight sill.
How do you anchor a sill plate?
Carefully place the sill place in the correct position and insert the wedge anchors into each hole through the sill plate. Hammer anchors into every hole ensuring that they are installed to the desired depth and securely in place.
What is the maximum distance between foundation anchor bolts for sill plates?
Bolts shall be embedded at least 7 inches (178 mm) into concrete or masonry, and spaced not more than 6 feet (1829 mm) apart.
What size anchors for sill plate?
1/2-inch-diameter
Wood sole plates at all exterior walls on monolithic slabs, wood sole plates of braced wall panels at building interiors on monolithic slabs and all wood sill plates shall be anchored to the foundation with minimum 1/2-inch-diameter (12.7 mm) anchor bolts spaced not greater than 6 feet (1829 mm) on center or approved …
What kind of wood do you use for a sill plate?
Sill Plate is a tough, versatile pressure-treated lumber. Like borate-treated lumber, it’s guaranteed to stop termites and prevent decay, plus it’s compatible with carbon steel (black iron) fasteners.
Can pressure treated wood sit on concrete?
Wood on Concrete or Other Masonry
Pressure-treated wood is not required if an impervious moisture barrier and a 1-inch metal or masonry pedestal separate the post from the earth by a total of 6 inches in basements or in weather-exposed locations.
Do floor joists sit on the sill plate?
The floor joists are secured to the sill joists by installing wall sheathing (plywood or OSB board) that laps from the sill plate up the wall to the double top plate. When the sheathing is nailed to the sill plates, rim joists, studs and double top plate, then all the components are secured in place.
Should you use pressure treated wood for a sill plate?
You need pressure treated lumber when: Sills and sleepers on a concrete or masonry slab that is in direct contact with the ground unless separated from such slab by an impervious moisture barrier. This includes the footing.
Does bottom plate have to be pressure-treated?
Pressure-treated bottom plates deal with the symptoms of the problem when a capillary break between wood and concrete deals with the cause. No direct contact, no need for pressure-treated bottom plates.
Does bottom plate have to be treated?
It is still a common belief that you don’t want to inhale the sawdust from treated lumber. But I think sawdust in general is bad for our lungs. But anyways, treated wood is required here for sill plates before floor joists, and that is considered indoors and has been for years.
