How do you remove an old metal P-trap?
Quote from Youtube video: So you want to buck it to catch the water. So it doesn't get all all over the place. Second thing you need is just some ranch or pliers or something big enough that you can get around here.
How do you replace a galvanized P-trap?
Quote from the video:
Quote from Youtube video: In this case if we were to screw a plastic washer onto this that sharp metal can cut into it so it's always good to go metal to metal plastic to plastic. I'm going to put the wall tube in first.
How do you remove a metal P-trap without a wrench?
Quote from the video:
Quote from Youtube video: Using your rag place it in your hand and grip the p-trap. Now grip the other side and you're doing this so you don't actually snap the pipe. And just turn it loosen up a little bit now do the other.
Which way do you unscrew a P-trap?
Unscrew the nuts holding a plastic P-trap by hand, gripping the trap firmly with one hand and rotating each nut counterclockwise. You must unscrew two nuts to remove the trap. One holds the trap to the tailpiece, the small length of pipe extending down from the sink, and the other holds the trap to the drain line.
How do you replace an old P-trap?
Quote from the video:
Quote from Youtube video: And then this cutter head will cut the pipe out without damaging the fitting. It's time to. Drill. The cutter head shreds the pvc. So i want to remove the debris. And keep. Cutting.
Can you replace a metal P-trap with a plastic one?
Take the drain assembly apart and separate it into its components so that you can replace each one with an identical plastic component. Besides the P-trap, there may be extensions and fittings, depending on the configuration of the sink in relation to the waste stub-out.
How do you remove an old metal sink drain?
Quote from the video:
Quote from Youtube video: Take your pliers loosen the locknut from the bottom. That may take a minute sometimes they're a little bit rusty. Once you get that removed. You'll want to work the drain assembly. Up.
How do you loosen a slip nut?
Quote from the video:
Quote from Youtube video: Put it over the nut. And try to break it loose you might want to wiggle it back and forth a little bit to get started. And then loosen it up.
How do you loosen a stuck pipe fitting?
Quote from the video:
Quote from Youtube video: Fitting use a regular propane or map gas torch to get it nice and hot. And then take the joint apart while it's still heated. That will make it a lot easier since the fitting expands.
How do you loosen a tight drain pipe?
Quote from the video:
Quote from Youtube video: So you want to grip it just enough that you have a hold on it. Then I take my pair of pliers. And I'll grip the other one and just give it a little twist. And they should come right apart.
What to do if P-trap is glued?
Cut two sections of PVC pipe (5 inches or longer) that are the same diameter as the existing pipe. Remove burrs. Apply PVC primer to one outside end of both pipes and the inside ends of a new P-trap. Apply PVC cement to all primed areas and push the cemented pipe ends into the ends of the P-trap.
Are all P traps the same size?
Traps come in 1-1/4 inch (standard bathroom sink) or 1-1/2 inch (standard kitchen sink) inside diameter sizes. Be sure to check so you get the right size replacement at your local store. In this guide we’ll show you how to replace a P-trap in a few easy steps.
How do you remove a pedestal sink P-trap?
Loosen the slip nuts at both ends of the P-trap using channel-lock pliers. First pull the P-trap apart from the outlet pipe in the wall, then gently separate the P-trap from the drainpipe by rotating it back and forth while pulling down. Be careful not to exert too much downward force on the suspended pedestal sink.
How do you remove P-trap cleanout plug?
Use an adjustable wrench or adjustable pliers to unscrew the clean-out plug from a P-trap. Place a bucket under the trap to catch the water that will spill out when you remove the plug. Turn the plug counterclockwise to remove it, install the replacement, and turn it clockwise to tighten it.
How do you tighten a drain nut on a pedestal sink?
Quote from the video:
Quote from Youtube video: And then just wrap it right around. There. Okay now you're going to put that in from the top i'm going to take this piece and push it in through from the bottom.
How do you remove a sink trap?
Quote from the video:
Quote from Youtube video: Slide it off dump the water in. There. Loosen up these nuts now loosen. Them up all the way. And you can leave them right on the pipes. And then you can pull this down dump out a little water.
