How do I hide my LED strip power supply?
Quote from the video:
Quote from Youtube video: You use three-quarter inch or larger double-sided foam tape you're going to need to trim it off if you use a half-inch. It should fit right on there. And you won't need to do any trimming.
How do you hide LED strips on the ceiling?
Quote from the video:
Quote from Youtube video: Make the LED the drop down ceiling. As usually within sort of 100 mil 50 mil away from the ceiling depending on your preference. But always hold the LED strips into place first.
How do you hide exposed LED strip lights?
Place your LED strips on top of floor molding to light up the room.
- Your LEDs will be hidden behind the floor molding and will light up your walls.
- Use anywhere from a 16.40 ft (5.00 m) roll to a 49.21 ft (15.00 m) roll, depending on the size of your rooms and how many rooms you want to illuminate.
Can LED strip lights be hardwired?
When hardwiring the strips, you will just need to make solid connections between all your strip wires to the output wires on the power supply. This can be done with wire nuts or wiring all strips to a common positive and negative wire so you can make a one to one connection with the hardwired power supply.
Can you put LED lights on the ceiling?
You can install LED strip lights around your ceiling by measuring ceiling perimeter length, using a high-quality strip with built-in adhesive, and opting to install the strip behind a recession or coving for a beautiful, dramatic yet luxurious lighting effect.
What power supply do I need for LED strip lights?
Whether it’s your cell phone, laptop, or in this case, LED strip lights, you’ll need something to take the 120 volts of alternating current (AC) from your wall outlet and convert it into a lower voltage of direct current (DC) that your LED strips (or other electronics) require to run.
How do you install LED strips on a ceiling?
Quote from the video:
Quote from Youtube video: The distance you'll be placing these moldings from the ceiling. Next step is preparing your components on a board that you will put up in the attic or whatever you wish to install it.
How do you install LED strips on the ceiling?
Quote from the video:
Quote from Youtube video: Two hours later got it that's what it looks like it's just four pins on either side. And it allows you to connect. One end of the LED strip into another. One more important thing when you're doing
Is it safe to cover LED lights?
Don’t cover LEDs with fabric.
It can be tempting to toss a shirt or scarf over those bright lights to block them from view, but it’s not a great idea. Fabric tends to trap heat, which could cause your electronic item to overheat and even become a fire hazard.
How do you hardwire strip lights?
Quote from the video:
Quote from Youtube video: You can wire the strip's to the switch. Connect the switch to the power supply. Then plug the power supply into the outlet and turn on your installed LED strips.
How do you hardwire LED lights?
Quote from the video:
Quote from Youtube video: Cut that plug off. And inside almost every light fixture. You're gonna see a little black and a white wire.
How do you hardwire a LED transformer?
Quote from the video:
Quote from Youtube video: The load and neutral wires are connected to switched power in the wall. And then we connect the output to the LED leads a switch.
Can I mount LED power supply in Wall?
The hardwired installation of the Power Supply should only be performed by a qualified electrician. Do not conceal the line voltage input cord or Power Supply inside a wall, ceiling, soffit, or similar permanent structure, unless consulting a licensed electrician.
Can you hardwire a low voltage transformer?
To hardwire a low voltage transformer, the main power should be turned off at the breaker panel before making any electrical connections. The transformer has at least four wires attached to it.
How do you install an outdoor low voltage transformer?
Quote from the video:
Quote from Youtube video: Slide the transformer aside and now drill the hole for the bottom anchor sleeve. Put your masonry anchor and screw together put them in the hole and secure. It down with the screwdriver.
What do you do with end of landscape wire?
Quote from the video:
Quote from Youtube video: So what you can do is get electrical tape and wrap it around it. You don't need to worry it won't cause any damage or harm anything. And that electrical wire will protect it however.
Can I use an extension cord for low voltage lighting?
An extension cord should never be used between the transformer and the electrical outlet. Plug the transformer directly into the power outlet. Low voltage outdoor lighting is not hard to install or maintain.
Can you plug a transformer into a power strip?
Yes you can do that, the reason you shouldn’t do it the other way is that you can turn the varistors into a conductor (by overvolting) creating a short circuit in the surge protector.
Can I use an extension lead with a transformer?
If using a transformer for 110V supply, NEVER connect a transformer to its power supply via an extension lead – though you can, of course, plug extension leads it the transformer’s socket outlets.
