How do you fix a loose tub surround?

Pull the edge of the tub surround away from the wall a little, then inject a little glue into the space. A spot of glue every three or four inches up and down the edge will do the trick. As for an adhesive, I recommend polyurethane glue.

How do you fill the gap between shower surround and drywall?





Be sure to use mesh tape in damp environments like the bathroom. Filling the gap means cutting the sheetrock so that it runs up to the edge of the enclosure’s mounting flange, pre-filling the recess with hot mud (setting compound), then taping and finishing with standard drywall compound to cover the joint.

How do you repair a tub wall?

Quote from the video:
Quote from Youtube video: And then one small sheet of 80 grit sandpaper. And a small application brush now do not throw the container away this is perfect for mixing up the epoxy.

Can you trim a tub surround?

Although tub surrounds come according to the size of your enclosure space, some cuts are required during installation. Specifically, installers must cut the surround walls to accommodate the faucet, shower head and other plumbing fixtures.

How much does it cost to replace a tub surround?

Cost To Install Tub Surround



The average cost to install a tub surround is $600 to $1,800 for the materials and labor. The labor cost to replace a tub surround is $300 to $600. Basic acrylic and fiberglass tub surrounds cost $200 to $1,000, while solid surface surrounds cost $600 to $2,000, plus installation.

How hard is it to replace a tub surround?





It’s not uncommon to be faced with major wall repair long before the tub is ready for replacement. This can a pretty difficult job if you have ceramic tile walls, and installing a new system of tub surround panels is usually an easier solution.

How do you fill the gap between tub and surround tub?

If you have tile on the wall adjoining the tub, select a caulk that matches the color of the grout. If your gap is smaller than 1/8 inch in width, use regular caulk; fill gaps larger than 1/8 inch with a sanded caulk. Make sure the gap is clean and dry, then squeeze a thin, even bead of caulk into the space.

Should I put drywall behind tub surround?

The short answer to the question is, “It’s not recommended.” However, this answer only really only suffices if you’re converting a room that was never a bathroom into a wet space. Drywall on its own is not suitable for use in bathrooms because it is prone to absorbing moisture and thus losing structural integrity.

What do you put behind a tub surround?

Install cement board or an equivalent moisture-resistant backing material on walls behind tub and shower enclosures composed of tile or panel assemblies with caulked joints. Don’t use paper-faced backer board, i.e., paper-faced drywall, behind seamed tub and shower enclosures.

How do you trim a shower surround?



Trim the Panel

  1. If you need to trim the panels for a proper fit, you can use a piece of masking tape on the panel to mark it. …
  2. Make your measurements and draw the cut line using a straightedge.
  3. Use a jig saw to cut the panel to the proper size.
  4. If you need to trim the corner panels, you can do that with scissors.

What is the best way to cut a tub surround?

Measure carefully, because the surround needs to fit snugly. Outline the area to be cut with some masking paper and draw your lines. Use a drill to poke a starting hole or two somewhere along one side of the window. Once the jigsaw can be inserted, cut the line as precisely as you can.

Can you cut fiberglass shower surround?

Use a jigsaw with a carbide tipped jigsaw blade to cut out patterns. Jigsaws will readily cut circles and angles for the perfect fit when installing fiberglass liners around faucets, shower heads, sliding doors and other shower stall accessories.

Can shower wall panels be cut?



Shower wall panels are super easy to install by anyone who is DIY competent. Simply cut the Showerwall panels to size and fix them to the wall or over existing tiles.

How do you cut fiberglass reinforced panels?

Saw straight cuts through thick panels using a carbide- or diamond-coated blade. When making straight cuts through thick pieces of FRP, choose a blade with either a diamond or carbide coating that will be strong enough to cut through the material.

Can you cut fiberglass tub with oscillating tool?

For straight cuts, the oscillating blade cutters are great. Also, wherever possible, you’re better off to make rounded (radius) cuts to relieve stress on the fiberglass.

Can you use a dremel to cut fiberglass?

The Dremel 561 is a high-speed cutter with a 1/8 in. steel shank. Ideal for cutting wood, plastic, fiberglass, drywall, laminate, aluminum and vinyl siding. This bit can be used in a variety of applications such as preparing an area for light fixtures or making cutouts in cabinets and paneling.

What is the best tool for cutting fiberglass?



Unlike other construction materials like plywood, fiberglass requires several precautions for a clean and safe cut. For straight cuts, a table saw or hand-held circular saw is sufficient. However, for curved cuts, a saber saw or hand-held jigsaw will do a fine job.

How do you cut a fiberglass tub?

The easiest way to get a fiberglass tub out of the bathroom is to cut it into small sections, which can be done using a jig saw with a fiberglass blade. You can find saws and saw blades at your local hardware store.

How do you remove a 3 piece tub surround?

How to Tear Out Bathtub Surround

  1. Take All Necessary Safety Precautions. …
  2. Remove the Faucet Screws. …
  3. Remove the Shower Head. …
  4. Take Off the Tub Spout. …
  5. Cut Rivets With a Utility Knife. …
  6. Place the Utility Knife Between the Surround and Wall. …
  7. Remove the Retaining Trim. …
  8. Start Pulling at the Upper Right Corner.

Can you use a chainsaw to cut up a hot tub?

Hot tubs can be cut up and demolished with a Sawzall saw. Before the hot tub is disassembled, all electrical and gas hookups must be disconnected, the hot tub must be drained, and the hot tub’s skirt must be detached. Safety gear should be worn while demolishing the hot tub to prevent injury.