How big of a hole can you drill in 2×4 stud?
2. Drilling. Any stud may be bored or drilled, provided that the diameter of the resulting hole is no more than 60 percent of the stud width, the edge of the hole is no more than 5/8 inch (16 mm) to the edge of the stud, and the hole is not located in the same section as a cut or notch.
Can you drill a hole through a king stud?
Quote from the video:
Quote from Youtube video: Business is you're not allowed to drill. Through a king stud a king stud is the board that runs vertical up and down and it's going to be next to the window you got your window trimmer.
Can you notch a stud?
1. Notching. Any A stud in an exterior wall or bearing partition shall not be permitted to be cut or notched to a depth not exceeding 25 percent of its depth width. Studs in nonbearing partitions shall not be permitted to be notched to a depth not to exceed exceeding 40 percent of a single stud depth width.
How do you knock out a drain hole on a washing machine?
Quote from the video:
Quote from Youtube video: With a hammer right there right there as you go around. So that can break that you can break that the bond.
Can you drill two holes in a stud?
Multiple holes (except 2 side-by-side holes only) must be drilled in the centerline of the stud. Side-by-side holes require steel plates on both faces. Holes should not be bigger than 40% of the stud width (max 1 3/8″). Notches should not be bigger than 25% of the stud width (max 7/8″).
Can you cut into a load-bearing wall?
Steps for Cutting a Pass-Through in a Load-Bearing Wall
Hammer the studs into the temporary wall until they’re snug. Use a drill/driver to secure a brace across the studs. Use a level to draw the outline for the opening. Cut the opening using a reciprocating saw.
Can you drill through a load bearing stud?
Drilling. Any stud shall be permitted to be bored or drilled, provided that the diameter of the resulting hole is not more than 60 percent of the stud width, the edge of the hole is not less than 5/8 inch (16 mm) to the edge of the stud, and the hole is not located in the same section as a cut or notch.
How many wires can be in a stud hole?
The Answer. According to the National Electrical Code, you can have 4 12/2 nonmetallic sheathed cables through a single bored hole that is fire- or draft-stopped using thermal insulation, caulk, or sealing foam, or where proper spacing is not maintained for more that 24 in.
Can you run drain pipe through studs?
The studs provide the strength and framework for the structure, and the empty spaces between the studs serve an important function, too: They provide the perfect place—a veritable vertical freeway—to run pipes, vents, drains, wires and ductwork.
How do I stop my washing machine from Backflowing?
Washing machine hoses need to be extended with large standpipes placed at least 36″ above the washing machine’s top. This will help prevent siphoning, which is when wastewater flows back into the washing machine, but it will also prevent wastewater from backing up into the washing machine.
How do you remove knockout plugs?
To remove a knockout, position the tip of a regular, blade-tip screwdriver just inside the edge, on the side opposite the attachment points. That ought to partially dislodge the knockout, allowing you to remove it the rest of the way by twisting back and forth until the attachment points snap.
Should I cut washer drain hose?
Either you have to replace the hose with a new one. Or, you have to cut the drain hose to a standard size. If you want to cut the hose, make sure you cut the end that goes inside the standpipe. Don’t make it too short, just make sure it doesn’t create any loops.
What height should a washing machine drain be?
In order for the drain hose on your Top Load washer to function properly, the drain must be at least 30″ up from the floor and less than 8 feet high. In order for the drain hose on your Front Load washer to function properly, the drain must be at least 24″ up from the floor and less than 8 feet high.
Can a washing machine drain hose be too long?
Make sure that the drain hose is not stretched, pinched, crushed, or kinked. Do not install the drain hose with the end lower than 29.5 inches (75 cm) or higher than 96 inches (244 cm) above the bottom of the washer or more than 60 inches (152 cm) away from the washer.
