Should concrete expansion joints be filled?

Just remember that expansion joints should always be sealed and filled with a flexible joint sealer and never epoxied or coated over. Contraction joints can be filled in the same manner after a coating or sealer is applied if you desire.

Should concrete control joints be caulked?





Caulking Concrete Cracks and Expansion Joints



Even expansion joints in your concrete driveway should be caulked. They can be the biggest culprit of water under your slabs. Notice how the caulking is slightly lower than the concrete slab around it.

How do you prepare concrete for a floating floor?

Quote from the video:
Quote from Youtube video: Check the moisture of both floors. And when you're installing a floating floor you must use a vapor barrier. Your concrete subfloor will also have to be sound enough to support the floor.

What do you use to fill control joints in concrete?

Quote from the video:
Quote from Youtube video: Step is to fill it with the product reason a caulk gun with this application we can also use a pneumatic gun to fill it in to. Start we taped both sides of the joint right in line at the joint.

How do you seal a control joint?

Quote from the video:
Quote from Youtube video: Press down on this little clutch. Pull the plunger. Back put the cartridge in bottom first push the plunger in and you're ready to go.

What is the purpose of a control joint in a concrete slab?





Contraction/control joints are placed in concrete slabs to control random cracking. A fresh concrete mixture is a fluid, plastic mass that can be molded into virtually any shape, but as the material hardens there is a reduction in volume or shrinkage.

Do expansion joints need to be sealed?

Expansion joints need to be sealed periodically to protect against water, dirt, and debris. These elements can hurt the structural integrity of concrete over time. Water can also lead to mold and interior leaks that are costly to repair.

How deep should concrete control joints be?

Concrete control joints should be no less than ¼ of the total thickness of the slab (1” deep for a 4” thick pour) and placed no less than 2-3 times (in feet) the thickness (in inches) of the slab (8-12 feet apart for a 4” thick pour).

Is it too late to cut control joints?

Joints should be sawed as soon as the concrete can withstand the energy of sawing without raveling or dislodging aggregate particles. For most concrete work, cutting should take place within the first 6 to 18 hours and never beyond 24 hours.

Should concrete cuts be filled?



Once the joint is cut into place, the joint itself is ready to do its job. The joint can then be left as is, sealed, or filled. Sealing or filling should be put off as long as possible to allow the joint to widen, although in practice joints are usually sealed or filled sooner than ideal.

What is filling control?

Filling systems require controls that can be set up by the filling hoppers so that the driver can decide which bin or silo to fill when delivering materials. The control system can also be placed in a location away from the hoppers, e.g. in the office of the plant supervisor.

Which is the material used for filling concrete joint?

Rubber, asphalt and other compressible materials are popular joint filler material choices. Joint filler also prevents the introduction of other materials that are not compressible from entering the joint, which could cause concrete failure as well.

Should you seal saw cuts in concrete?



Because the sawed crack control joints offer a point of ingress for water and incompressibles into the pavement structure and base, it’s perceived by most road agencies that they should be sealed to keep water and debris out of the structure.

What is expansion joint filler?

Expansion joint filler is a term used to describe a group of weatherproofing products intended for use as an aesthetic or functional expansion joint sealer agents in gaps in concrete slabs, walkways, decks, bridges, and sidewalks, for instance.

How do you fill a 2 inch gap in concrete?

Quote from the video:
Quote from Youtube video: Now if i have any large holes where voids are starting to form underneath the concrete. I do recommend some sand for that and filling those voids in before you seal off the top with the tremco.

How do you fill a 1 inch gap in concrete?

Quote from the video:
Quote from Youtube video: And twigs and sticks and dirt out of the gap. But now what i want to do is just go through with. Some. General purpose sand.

How big can a concrete slab be without expansion joints?



Rule #1 – Keep joints as square as possible. Rule #2 – In order to prevent intermediate cracking, space joints (in feet) no more than 2 – 3 times the slab thickness (in inches).

How do you fill slab joints?

Quote from the video:
Quote from Youtube video: First thing to do is to get a fairly dry mix of mortar. This is for parts building sand with one part cement. It's just damp enough to stick together no damper than that otherwise it stains the slabs.

How do you fill large gaps in concrete?

Wide cracks in concrete are best patched and sealed with a concrete patching compound. Smaller cracks, less than 1/4 inch wide, can be repaired with a concrete caulk or liquid filler. Patching compounds typically are mixed with water and applied with a trowel.

How deep should polymeric sand be?

1 ½”



Polymeric Sand needs a minimum depth of 4 cm (1 ½”) to be effective. Use a power washer to empty the joints. If there is already polymeric sand between the pavers, soak the sand to soften it up before emptying the joints.