The sub-material is often destroyed in the removal process because of the force necessary for removal of the product. DITRA, being textured, would hold onto the mortar used to mount the tile. The only thing more complicated about demo where DITRA is involved is it’s one more layer to be removed.

What machine do you use to remove tile?

Use a ball peen or masonry hammer and cold chisel to tap the pieces free. Always wear safety glasses when removing ceramic tile. In some cases, the only way to tear out the ceramic tile is with heavy equipment such as a jackhammer or air chisel.

How long after laying DITRA can you tile?





Once DITRA has been installed on the substrate, tile can be installed right away. No need to wait for the mortar to cure.

How do you remove tile over DITRA heat?

Quote from the video:
Quote from Youtube video: So we have a couple of ways to do that. We have a mylar sheet that actually detects heat. So we could lay this over the top of the tile.

Can you use DITRA under porcelain tile?

1 to install ceramic. (including porcelain) and stone tile over DITRA and DITRA-XL. Portland cement-based unmodified thin-set mortars are dependent on the presence of moisture for hydration in order to gain strength. Since DITRA is impervious, it does not deprive the mortar of its moisture.

What is the fastest way to remove tile flooring?

Quote from the video:
Quote from Youtube video: So we're gonna start moving it we're gonna start with just a cold chisel right here a wide chisel and a hammer. It's gonna start chiseling this stuff away it should have some Hardiebacker.

How hard is it to pull up tile floors?





Quote from the video:
Quote from Youtube video: The best way to remove tile is to use a hammer and a chisel setup. And get underneath it and basically pry it up you just need to find a spot along the edge of the tile.

Is it OK to walk on DITRA?

Pro-Tip: DITRA can be walked on immediately after; there’s no need to wait for the mortar to cure.

When should you use DITRA?

DITRA is specifically designed to allow the installation of ceramic and stone tile over any even and load-bearing substrate. The integration of DITRA’s uncoupling, waterproofing, load-distribution, and vapor management functions makes consistent results viable.

How long till you can walk on DITRA?

Ditra-set only takes 25 to 30 minutes to dry. These advantages allow you to walk on the Ditra surface before tiling or even right after installing the Ditra. When installing ceramic and other stone tiles, Ditra is beneficial to use.

Can you put DITRA over tile?



Schluter®-DITRA is specifically designed to allow the installation of ceramic and stone tile over any even and load-bearing substrate.

What happens if you use modified thinset on DITRA?

The Schluter website says it is fine to use MODIFIED thinset to adhere the Ditra to the plywood subfloor, however they specify UNMODIFIED thinset to adhere the tiles to the Ditra.

Is DITRA set modified or unmodified?

Bostik Ditra-set



This was (is) an unmodified LFT mortar that can be used to install Schluter products.

Do I need DITRA over plywood?



Quote from the video:
Quote from Youtube video: So you can waterproof the entire floor. And it also protects your tiles. And grout from cracking. So those are some reasons why we use Detra.

What type of thinset do you use under DITRA?

unmodified thin-set mortar

To set DITRA over concrete or gypsum, Schluter-Systems recommends an unmodified thin-set mortar meeting the requirements of ANSI A118. 1.

Should I use DITRA over concrete?

Yes, writes Doug McEvers, Ditra will insulate the concrete slab from the tile and lower the potential for thermal storage. “There is nothing wrong with tile laid directly on concrete providing all precautions are taken regarding moisture proofing,” he says. “Tile and grout work loose if the underlayment flexes.

What is the difference between DITRA and DITRA-XL?



Quote from the video:
Quote from Youtube video: Used when you have 24 inches on Center joists spacing minimum thickness 3/4 inch plywood OSB. Then dieter Excel would be your best bet there. So that's what the difference is between the two.

Can porcelain tile be laid directly on concrete?

You can install the tile directly on the concrete. You can install a CBU or cement board on the concrete, then the tile on top of that. Finally, you can use an uncoupling membrane between the tile and the concrete.

What do you stick DITRA matting down with?

Installing DITRA Matting

  1. Apply a layer bonding adhesive like Ardex AF200 to the level substrate using a 3x3mm or 4x4mm notched trowel.
  2. Cut DITRA matting to size if required, then embed the anchoring fleece on the underside of the matting into the adhesive so that its entire surface is strongly bonded.

How thick is DITRA installed?

DITRA is 1/8″ (3 mm) thick, which minimizes tile assembly thickness and reduces transitions to lower surface coverings (e.g., carpet, engineered wood, and vinyl). DITRA allows for ceramic tile application over single-layer plywood or OSB subfloors on joists spaced up to 19.2″ (488 mm) o.c.