You don’t need drywall, but the cables that are considered “exposed to damage” need to be protected. Drywall is one way to do that.
What can I use instead of drywall in my basement?
Drywall Alternatives
- Wood Planks. Wood planks are an age-old drywall alternative that has certainly stood the test of time well. …
- Veneer Plaster. …
- Lath & Plaster. …
- Plywood and Sheet Wood. …
- Texture Wall Panels. …
- Brick & Masonry. …
- Exposed Concrete Block. …
- Cement Board.
How do I run wires in my finished basement?
Quote from the video:
Quote from Youtube video: Below these clips are keeping a piece of paneling that i custom cut to fit in here. Okay and i'm gonna open this up in a second and i can show you how this. Works.
How do I run Romex in my basement?
Running Romex Wire in Basement
You will have to drill a hole in the floor plate (attic) and roof or wall plate (basement) to run the wire. Make sure it is in the same wall cavity as the outlet you are trying to run the Romex to, since you can’t leave it exposed.
Can you drywall a basement ceiling?
Installing basement drywall ceiling is the most cost effective methods to cover the floor joists and beams, and finishing your basement ceiling properly.
Can you finish basement walls without drywall?
Use furring strips attached to basement walls: basement panels can be used in a basement finish not using studs and drywall. As such, all you need for support are some furring strips attached to basement concrete side walls.
How do you finish a concrete basement wall without drywall?
Finishing Basement Walls Without Drywall: Options and…
- Paint.
- Basement Panels.
- Wood Fiberboard.
- Fabric.
- Vinyl and Wallpaper.
- Stone Veneer.
- Pargeting.
- Exposed Brick.
How do you run electrical wire in an unfinished basement ceiling?
Where cable is run at angles with joists in unfinished basements and crawl spaces, it shall be permissible to secure cables not smaller than two 6 AWG or three 8 AWG conductors directly to the lower edges of the joists. Smaller cables shall be run either through bored holes in joists or on running boards.
Can Romex be exposed in basement ceiling?
Romex is fine when it is inside a wall/ceiling/floor because it is protected from puncture/cuts/etc. but if it is just running along the exposed walls of a basement that is not up to code.
How do you run an electrical wire through an unfinished wall?
Quote from the video:
Quote from Youtube video: Or an anchor before the wire has to go through the wall. So you would actually have to loop the wire up and back down in order to have that room to staple it and then get to go through the hole.
Should I put drywall in my basement?
Due to the often damp conditions of the basement, be sure to choose sheetrock that is at least moisture-resistant (often call greenboard) but be on the lookout for products that are specifically resistant to mold and mildew (some kinds of purple board).
Should you insulate a finished basement ceiling?
Yes. Faced insulation is actually recommended on basement ceilings and ceilings in general. The covering or “face” of the insulation prevents it from falling out and trickling down into the basement air. This is especially advantageous if the insulation is made of fiberglass, which can harmful if it’s ingested.
How much does it cost to drywall a ceiling in the basement?
Drywall: It costs around $1.50 per square foot to hang drywall in your basement. Ceiling: Basic ceiling installation can cost as little as $1-2 per square foot. But, if the project is complex, it can cost around $6 per square foot.
How much does it cost to drywall a 1000 sq ft basement?
Cost to Drywall a Basement
Installing drywall costs an average of $1,850 or about $2 per square foot.
What kind of drywall do you use for a basement ceiling?
If you’re drywalling your basement, you’ll need to use ½ inch thick gypsum panels on the walls and ⅝ inch thick sheets on the ceiling. If your basement is subject to moisture (most basements are), it’s wise to use water or mildew-resistant drywall.
How much does it cost to put a ceiling in a basement?
Raising a basement ceiling typically costs about $19,200 and can range from $16,000 to $24,000. During this process, the house is lifted and the foundation is raised to a new level.
Is it cheaper to drywall or drop ceiling?
Drop ceilings are more expensive to install than drywall making drywall the cheaper option. However, if you can install a drop ceiling by yourself, you can save on labor costs. You should also factor in paint costs for a drywall ceiling and whether you are hiring a professional to install and paint for you.
What is the cheapest ceiling to install?
Installing a drywall ceiling costs $300 to $400 for a 150-square-foot room. Expect to pay $2 to $3 per square foot for labor and materials. Standard, smooth drywall ceilings are the easiest and cheapest to install. They look great in any room, especially when painted the same color as the walls.
Is finishing the basement worth it?
Many people wonder if finishing their basement is worth the time, effort, and money to remodel their downstairs space. To answer that directly, yes, finishing your basement will almost always increase the value of your property. The standard return is around 70%, according to Remodeling.HW.net.
How do you half finish a basement?
SHARE
- Keep the ceiling exposed. This smart basement renovation reveals a key secret to enjoying a partially finished basement: Keep the ceiling open. …
- Ditch the drywall. …
- Capture the power of white. …
- Establish a focal point. …
- Get creative with paint and decor. …
- Install cabinetry. …
- Just do the basics. …
- Dress up with shine.
Why don’t people finish their basements?
New homeowners have their financial limits when it comes to adding any “nice-to-haves”. This may be a reason why basements are often left unfinished. Yet homebuyers have many reasons to extend that extra money to finish this often-neglected part of the home.
