How do you attach rigid foam insulation to concrete?

Quote from the video:
Quote from Youtube video: It into the position you want pull it away for about thirty seconds it lets the the glue itself kind of start to react and then press it back on and chances are it'll stay there all on its own.

How do you frame a concrete wall?





Quote from the video:
Quote from Youtube video: Next we will apply adhesive to the floor using a caulk gun to help secure the bottom plate. Of course let's put the board on the adhesive. Then pick it up. And put it back down on the ground lining.

How do you finish a concrete wall?

Quote from the video:
Quote from Youtube video: I'm gonna be troweling it and then using some bow arrow flex trials to do the trowel you'll probably end up using this size right here I got multiple trials I can use I have to tape off my surfaces.

How do you install rigid foam insulation between studs?

How to Install Rigid Foam Insulation Between Studs

  1. Measure the Project Area. Measure the entire wall area to figure out the amount of rigid foam to purchase. …
  2. Measure Individual Cavities. Measure each bay individually. …
  3. Mark and Cut the Rigid Foam. …
  4. Install the Rigid Foam Insulation. …
  5. Seal the Gaps in the Insulation.


How do you install rigid foam insulation on exterior foundation walls?





Quote from the video:
Quote from Youtube video: And an air barrier fully adhered to the foundation. We finish the insulation foam with a parched coat that's applied over a plastic mesh. And then painted.

How much space should be between studs and basement walls?

Be sure to maintain the 16-inch on-center stud spacing, and check the wall frame to make sure it’s plumb before nailing it to the beam.

Should you put a vapor barrier on basement walls?

Building codes usually require a vapor barrier (4 mil plastic sheeting) on exterior basement walls if the framing is attached to masonry or concrete surfaces, or if the wood framing butts up against the outer basement walls.

What should I put between drywall and concrete?

The solution is covering concrete with a vapor barrier, which acts like a resistant cell membrane instead. With a shield in place, the drywall is safe. Typically, a stud wall is then installed against the concrete, but furring strips are quick, easy and take up less space.

Should you seal basement walls before finishing?



Water issues can cause serious damage and ruin your investment. Before finishing the basement, deep-seal your concrete against water seepage, water vapor, and soil gases like radon.

How do you stud a basement wall?

Quote from the video:
Quote from Youtube video: And a couple of impact nails and what this does is this drives down it's a three inch nail goes through the one-and-a-half inch plate into the concrete. And even if it isn't completely buried.

Do you need to insulate basement walls below grade?

Your best bang for the dollar in this instance is to insulate the coldest part of the wall, again typically to 2-feet below grade. However, there are many instances where insulating the full wall is the best option, such as if your walls are stone, or the floor is earth or crushed stone with no vapor barrier.

How do you insulate basement walls with rigid foam?



Quote from the video:
Quote from Youtube video: Position the board's vertically. Using a level to ensure they are plumb against the wall. Notice how the notched edges fit together to create an insulated channel with no energy robbing air gaps.

Does rigid foam insulation need vapor barrier?

Foam insulation usually does not require a vapor barrier. For some foam insulation types, such as closed-cell spray foam and foam board insulation, the insulation itself stops the movement of most water vapor.

Does foam board go between studs?

Rigid foam board pieces are difficult to fit snugly between studs so you would have to spray foam to fill any gaps. Unlike loose-fill or batt, foam board insulation can’t easily be cut to perfectly contour around pipes or wires.

How do you cover rigid insulation on a foundation wall?

The most common approach is to apply a stucco-like “parged” finish with a surface-bonding cement. These finishes range from a thin paint-on coating to a thick acrylic-modified mortar applied over hardware cloth or metal or fiberglass lath. The thin paint-on coatings are easily chipped and prone to peeling.

What is the R-value of 2 foam board?



With an R-value of 13.1 for a 2″ thick sheet only two 2″ sheets are required to achieve R-25. 2. Extruded polystyrene or XPS (foam is usually pink or blue) XPS has an R-value of 5 per inch of thickness requiring 5″ of insulation to achieve R-25.

Which side of foam board insulation faces out?

The reflective side of the board should be oriented to the exterior and the non- reflective white side should be oriented to the interior. EXCEPTION: If vinyl siding is to be installed over AP™ Foil- Faced sheathing, install foam boards with the white nonreflective side toward the vinyl siding.

What is the difference between pink and blue foam board?

Both are manufactured using the same process and contain similar chemical components. The two products also have the same insulating power. However, blue foam boards are manufactured by Dow Chemical Co. whereas the pink foam boards are manufactured by Owens Corning company.

How do you fasten rigid foam insulation?

Apply a bead of construction adhesive to the part of the studs you will cover with the first sheet of insulation. Press the insulation sheet firmly in place, and hammer cap ring-shank nails into the studs at 6-inch intervals.