Can I plug the drain in my basement?

While covering a floor drain isn’t a good idea for basements prone to flooding during heavy rains, you can cover a basement floor drain using either a cover specially designed to plug this type of drain or good old-fashioned cement.

How do you cover a cleanout plug?

Quote from the video:
Quote from Youtube video: Here's how to install your creative clean-out cover first remove the existing screw and clean out cover next install the new screw.

What is a clean out plug in basement?

A cleanout plug is a cap or lid used to close off a drain cleanout pipe. The term cleanout or cleanout pipe may refer to any branch of a plumbing pipe that is used for cleaning or unclogging the system.

How do you hide a cleanout?

Quote from the video:
Quote from Youtube video: Cut the pipe a few inches below the ground. Level after cleaning the pipe glue the new clean-out fitting in place. Place the valve box in the ground and backfill around it.

How can I hide my basement drain?

If you have several pipes together in one or more locations, you may be able to hide them with a box. If you are handy with a hammer and saw, frame a box around your pipes and then wrap it with paneling or drywall. Finish and trim as needed and stand back to admire your work.

How do I find the drain in my basement?

Quote from the video:
Quote from Youtube video: So what it is is it puts a signal into the line or conduit you're trying to locate and then with this wand you're able to go along and detect it under the slab or underground.

How do you remove a sewer cleanout cap?

Driving a screwdriver at an angle into the outer edge of the cap. Then tapping it with a hammer to pry it open little by little. Directly tapping the fitting on top of the cap with small sledgehammer to get a little bit of movement. Again, if you accidentally break the cap, they are cheap to replace.

How do you hide sewer covers?

How to Disguise Drain Covers in a Garden or Backyard

  1. Use plants to disguise the drain cover. …
  2. Buy a fake “mock rock” to cover the drain cover. …
  3. Incorporate the patio stone onto the drain cover. …
  4. Create your own art mosaic drain cover disguise. …
  5. Paint the drain cover. …
  6. Disguise the drain cover with a birdbath or bird table.

How do you cover a sewer pipe?

How to Cover a Sewer Pipe in the Back Yard

  1. Cover the main pipe with a couple inches of gravel. …
  2. Sprinkle grass seed over the soil by hand or with a seed spreader. …
  3. Cover the grass seed with a light sprinkling of straw. …
  4. Hide the sewer pipe access point with small shrubs or a combination of fake and natural rocks.

How high should plumbing cleanout be?

Cleanouts on 6-inch (153 mm) and smaller pipes shall be provided with a clearance of not less than 18 inches (457 mm) for rodding. Cleanouts on 8-inch (203 mm) and larger pipes shall be provided with a clearance of not less than 36 inches (914 mm) for rodding.

How do you cover drain pipes on the wall?

You can purchase plastic or wooden pipe coverings at most hardware stores to match your decor. Simply spray some adhesive spray over the pipe and wrap your covering around it. Once you’re done, cut off any excess with a box cutter or a utility knife – be careful and watch your fingers!

Is a basement floor drain necessary?

Most homes built today are required by local code to have floor drains that lead to a collection pit where a sump pump carries the water to the surface.

How do you make a false wall to hide pipes?


  1. Plan the Wall. Determine the exact spot where you can erect a full framework that extends from the floor to the ceiling. …
  2. Nail Down the Base. …
  3. Measure and Cut Vertical Studs. …
  4. Build the Framework. …
  5. Set the Framework in Place. …
  6. Add Drywall. …
  7. Paint the Wall. …
  8. Add Outlets and Hookups.

What is the purpose of a false wall?

A false wall is an effective way to screen off an area from view. False walls are often used in high-end home entertainment systems to install projection screens and to conceal speakers. However, a false wall can also be useful for obscuring plumbing pipes and electrical conduit in a laundry room or basement.

What is a false wall called?

Knowing how to build a “fake” wall, more appropriately known as a temporary wall, can come in handy when you want to enhance your privacy or change the layout of a room without actually altering its construction.

How do you box in exposed pipes?

Quote from the video:
Quote from Youtube video: So first I'm gonna fix this pattern onto this wall to do this using hammer fix fix things basically need to drill a hole through the wood through the wall. And then just hammer it. In.

How do you make a box hide with pipes?

Quote from the video:
Quote from Youtube video: To cover it we used a cut down piece of plywood to the same width. And more drawing around pipes there's a lot of pipes here but leaving half an inch allowance.

What are pipe sleeves?

Pipe sleeves are a metal covering that fit over your copper pipes that comes out of the floor and go into your radiator. They’re a fantastic way of supercharging your radiator valves and making them look even more stylish.