Drywall is not an adequate backing material for a tile shower. Even moisture-resistant drywall (often green or blue in color) is not durable enough to withstand water exposure. Over time, the drywall will deteriorate from moisture, causing your tile to sag, crack, or fall out.
How do you transition from tile to drywall in a shower?
Quote from Youtube video: So there's a couple ways to waterproof. This you can either use sheet membrane. Like this rss sheet membrane or kerdi. And you would just cover the transition. Like so up to the black sharpie.
Should you tile the top of a shower?
If your bathroom tends to get humid or you are installing a steam shower, you should tile the ceiling to help protect it from moisture. Otherwise, the best time to install tile on the ceiling is if you are doing an accent wall in the shower, and want to extend the tile overhead.
How do you finish drywall where you meet the shower?
Quote from the video:
Quote from Youtube video: And then run it over the top and run it up against the top not a bad option the other option of course is to just mud it and then run mesh tape over the top mud it again with a skim coat and sand it.
Can you tile on top of a shower base?
You can put tiles over existing tiled shower pans as long as they are structurally intact, have no visible damage and do not leak.
How high should tile go above shower head?
Tiles should cover ¾ of the bathroom walls depending on the bathroom wall height and 4-6” above the showerhead.
What do you put on ceiling above shower?
You can go for regular drywall in ceilings above the non-shower or tub areas of your bathroom. However, for the space where the shower is located, it is recommended to pick moisture-resistant drywall or green board.
How far up the bathroom wall should I tile?
The classic design feature is usually between 34 and 54″ high, with 36″ being the average height. A classic offset or straight set pattern in a standard field size tile works best for this wall height. For a truly classic look, finish the top with a decorative trim or a bullnosed edge.
How do you finish where tile meets the ceiling?
Apply silicone caulk with the caulk gun, covering the grout joint. Use a wet finger to smooth the caulk joint where necessary. You want the caulk to adhere to both the tile and the ceiling and cover the grout. This will give a flexible joint to allow for movement between the ceiling and the wall.
How far should tile go past shower door?
Plan to extend the tile 2 or 3 in. beyond the tub and to leave at least a half tile along the wall if possible. Don’t stop tile even with the end of the tub. This leaves the walls along the front of the tub vulnerable to water damage, and doesn’t look as finished as tile extending to the floor.
How do you finish the outside edge of a tile shower?
Quote from the video:
Quote from Youtube video: Done is found these strips that can be added to the edge of the tile to hide that cut edge or hide the end of the edge of the tile.
How far above the tub should a tile be?
Bathtubs, believe it or not, will expand when filled with water. Leaving a 1/16″ gap between the tub and tile will prevent the tile from cracking when the tub expands. Plus, a 1/16″ gap allows the caulk to properly fill the space and waterproof the transition between the tile and tub or shower.
When tiling a shower where do you start floor or walls?
The tile installation principle is that the tiled wall ‘hangs’ over the tiled floor. The best way to achieve this outcome is by first tiling the floor so that the wall tile will then seem to be ‘sitting’ on the bathroom floor.
In what order do you tile a shower?
How to Install Shower Wall Tile
- Step 1: Choose Your Shower Wall Tile. …
- Step 2: Plan Your Shower Tile Pattern. …
- Step 3: Apply the Tile Mortar. …
- Step 4: Cut and Set the Shower Tile. …
- Step 5: Add the Bottom Row of Shower Tile. …
- Step 6: Apply the Grout. …
- Step 7: Cleaning the New Tile. …
- Step 8: Seal Off the Grout and Tile.
How much space should be between floor and wall tiles?
When you install ceramic tile on the floor, you must take care to create an expansion joint between the walls and the tiled floor. The Tile Council of North America recommends at least a quarter-inch gap between the tile floor and the walls. Never fill this gap with grout, because tile grout is not flexible.
