How do you cut angles for fascia?
Set the angle of a miter saw to 45 degrees so you can make clean cuts through the board. Put on your safety glasses, and position the fascia board so the corner on one end lines up with the saw blade. Turn the saw on and pull it down to cut the angle. Cut the ends of any other boards that will be on a corner.
How do you miter fascia corners?
Set a length of fascia board in the vise of the power miter box. Set the end of the board 1/2 inch past the tip of the miter box blade. Turn the vise handle clockwise until the board is secure. Pull the trigger of the saw and lower the blade to cut a miter on the end of the board.
How much do you overlap fascia?
NEVER ‘face nail’ fascia. DO NOT drive nails tight — fascia must be ‘hung’, only snug to soffit, to allow expansion and help prevent distortion. Allow at least 1″ overlap of fascia where lengths meet.
How do you measure for fascia?
Multiply the 1-1/2 inch width of the fascia board by the slope of the roof (e.g. 4/12). 1.5” times 4 divided by 12 = 0.5 or ½ inch. For a 2×6 fascia board at a 4/12 slope, the trim size would be 1-1/2 inch x 5 inches for an overhang without a soffit.
How do you cut a 45 degree fascia?
Quote from the video:
Quote from Youtube video: You cut that through. So then what we do is then cut this on the 45 on the back cut cut that all the way through. And then that will see it into place nicely on the pitch of the.
How do I make fascia corners?
Quote from the video:
Quote from Youtube video: We're going to do both sides first and then put the front piece on so we can cover the corners now the gable piece is a little trickier.
Can I use 2×4 for fascia?
Install the fascia so the bottom edge of the roof sheathing will rest on the beveled edge. Install 22-1/2″ long 2x4s between the trusses to support the fascia boards where they butt.
How do you fix corners on fascia boards?
Quote from the video:
Quote from Youtube video: And it splits real easily all you need is an 8 or 10 penny finishing nail on there galvanized finishing nail and you can secure this really well without splitting this wood.
How do you join fascia boards?
Quote from the video:
Quote from Youtube video: Because we want the boards to be able to move to expand and contract its importantly you only fix the joiner or corner to one of the boards. One side you fix using either a poly top pin or superglue.
What size should fascia boards be?
Fascias are typically made from 1-inch material, with the width being enough to cover the rafter width. Typically rafters will range from 2×6 to 2×8, although some are larger depending on the roof construction. Therefore, the more common fascia board sizes are 1×6 or 1×8.
How do you calculate soffit and fascia?
Multiply the total length by the width to obtain the area of soffit needed to fill the gap. For example, if the total eaves length is 110 feet, and the width is 2 feet, multiply 110 by 2. The result, 220 in this example, is the number of square feet of soffit required.
Where do you nail your fascia?
Quote from the video:
Quote from Youtube video: Start installing the fascia along the eaves by sliding the fascia under the roof drip edge and covering the ends of the soffit panels use pre paint and nails to attach the fascia to the sub fascia.
How far apart do you nail fascia?
Never face nail fascia. *Keep nails lined up with soffit V-grooves for best appearance. Nail every 24″, but do not nail too tight. Nails should penetrate a minimum of 3/4″ into nailing surface.
What kind of nails should I use for fascia?
You must use exterior grade nails. A finishing nail, which has a smaller head and can be countersunk, will give a clean look but nails with a head will be more secure. You can hammer it farther into the wood and cover with putty, caulk or wood epoxy before you paint.
How often do you fasten fascia?
Fascia: Install screws at a maximum 12-inch interval, with three screws across the face at each interval. Risers: Install screws at a maximum of 12-inch interval, with two screws across the face at each interval.
How do you overlap fascia trim?
Quote from the video:
Quote from Youtube video: All right i want to show you up close. So as you can see here that is your bird box wrapped an aluminum fascia. And that is your soffit. Running up the gable end to sum up everything all you're going
Can you use deck boards as fascia?
Another option is to use two deck boards as fascia. Customers often chose this option if they want to match an exact color to their decking, border, or railing.
How do I install fascia board by myself?
Quote from the video:
Quote from Youtube video: You put the one side of the fascia. Board up on the l bracket that we made. And then you just grab the other side as you just see me do there and carry it up the ladder.
How thick should fascia boards be?
1″
Fascia is the term given to the horizontal board that is fixed along the rafter ends at the eaves, closing the gap between each rafter. Traditionally made of 3/4″ or 1″ thick timber, PVC has in recent years become the material of choice for most contractors and developers due to its maintenance-free appeal.
What is the best wood to use for fascia board?
Many different types of wood are suitable for fascia boards. Spruce, pine and fir are all popular and relatively inexpensive options. However, some roofers prefer to use cedar, cypress or redwood for fascia boards. While they are more expensive, these woods better resist moisture, even when left unsealed.
