What does the little hose in the toilet do?
That tube provides water to refill the bowl. Without it, you’d only refill the tank. During the flush, the siphoning action through the trap pulls more water out of the bowl than is necessary to maintain a water seal, the water is replenished by the bowl refill.
What is the hose attached to the toilet?
Many people choose bidet sprayers because they are so simple to install. You’re just adding a valve to the water connection under your toilet! This diverts clean water before it reaches the toilet and sends it to the flexible bidet hose and bidet spray head.
What is the floating thing in the toilet tank?
A ballcock (also balltap or float valve) is a mechanism or machine for filling water tanks, such as those found in flush toilets, while avoiding overflow and (in the event of low water pressure) backflow.
How do you fix a toilet tank hose?
Quote from the video:
Quote from Youtube video: Valve. Now grab your new hose. Begin by threading the metal connector nut onto the shut-off valve. And hand tighten. Then use a wrench tighten. About one to one and a half turns.
How do you remove a plastic toilet supply line?
Quote from the video:
Quote from Youtube video: You can see here we're kind of just dripping right now. Now the way to remove these is you turn counterclockwise. And you pull in a gentle motion. You can see here it's coming loose.
Where does the water tube go in the toilet tank?
The Overflow Tube empties directly into the toilet bowl. This water raises the water level in (refills) the bowl. If it weren’t for the Refill Tube there would be only a small amount of water in the bottom of the bowl. The Refill Tube must be located above the Overflow Tube.
What connector do you need to attach the water line to the tank of a toilet?
Connect the shut-off valve to the toilet with a standard toilet supply hose that has a 3/8-inch compression fitting on one end and a 1/2 FPT fitting to fit the tank inlet on the other. If your toilet is in a basement or another cold, damp place, water condensation on the tank can drip onto the floor and saturate it.
How do you replace a toilet overflow tube?
Quote from the video:
Quote from Youtube video: And the actual bowl portion of the toilet. And then you'll get that on top you just simply after that's in place you'll simply just reattach this chain to the handle.
How do you remove a plastic push fitting?
Quote from the video:
Quote from Youtube video: What you might find is insert gets stuck in there. Now you can pull it out with a pair pliers or just untwist the whole thing.
Can you remove hose from flowtite valve?
Quote from the video:
Quote from Youtube video: We go there you go it comes off pretty easy and remove that valve you just pull towards you a little bit. And you twist it counterclockwise. And as you twist counterclockwise. It should come right.
How do you remove a push off valve?
Quote from the video:
Quote from Youtube video: Go to each of your faucets in the household. And just to verify all that water is out of the plumbing prior to opening up that valve. And removing it from the capital. Lines as well as the adjustable.
How do you replace a plastic plumbing shut off valve?
How to Replace Plastic Plumbing Shutoff Valves
- Shut Off the Main Water Valve. Turn off the main water valve to the house. …
- Cut the Plastic Pipes. …
- Apply the PVC Primer. …
- Primer and Cement. …
- Unscrew the Ring-nut. …
- Primer, Cement and Push. …
- Align and Tighten. …
- Shut off the PVC Ball Valve.
How do you replace a PVC toilet shut off valve?
Quote from the video:
Quote from Youtube video: Allow the joint to cure according to the solvent's instructions finish by installing your faucet or toilet connector from the stop valve to your fixture. Hand tighten the nut until snug.
How do you remove a PEX shut off valve?
Quote from the video:
Quote from Youtube video: So you need to grab the pipe. And try to pull it up okay and see if there's slack in underneath the floor.
How do you change a PEX toilet valve?
Quote from the video:
Quote from Youtube video: Cut the PEX tube. So the end is square. And free of any burrs or damage or buildup on the surface. Next slide the crimp ring over the tube.
How do you remove PEX plastic fittings?
Quote from the video:
Quote from Youtube video: Gently work the tubing back and forth while slightly pulling away from the fitting until they separate. When making a new fitting connection always ensure that the system is deep pressurized.
