What Causes Thermostat Not Reaching Set Temperature Problems?

  • The thermostat is either broken, dusty, or not level.
  • You need a simple recalibration.
  • Loose wiring is causing a thermostat problem.
  • Your HVAC system is too small for your home.
  • The thermostat is in a location that is not optimal.

Why won’t my thermostat let me adjust the temperature?

Sometimes when the room temperature doesn’t match the thermostat setting, the problem could be a dirt buildup in its interior parts. As part of a furnace or air conditioning tune-up, a professional will inspect and clean the wiring of your thermostat so you won’t have to worry about this issue!

Why does my furnace kick on when the temp is higher than it is set at?

When your furnace keeps running after the temperature has been reached: Check the blower motor – Your forced air heating system uses a blower to push air through ducts and into your living space; sometimes, the blower runs at the same time that your furnace is heating the air, but sometimes it runs on its own.

How do I fix an unresponsive thermostat?

If the thermostat is still unresponsive, make sure the breaker is shut off and remove the cover. If it looks dirty inside, use canned air or a soft artist brush to clean away accumulated grime that may be affecting its functionality. Then look for issues like loose wiring or terminal screws and tighten them up.

Why can’t I adjust the temperature on my Honeywell thermostat?

One of the most common causes of a thermostat not reaching the set temperature is a damaged or broken sensor. When a sensor is the issue, the thermostat’s reading of the surrounding temperature will be incorrect.

How do you know a thermostat is bad?

7 Ways to Tell Your Thermostat Is Broken

  1. Thermostat Has No Power. …
  2. AC or Furnace Won’t Turn On. …
  3. Heater or AC Won’t Turn Off. …
  4. Thermostat Doesn’t Match Room Temperature. …
  5. Thermostat Doesn’t Respond. …
  6. Short Cycling. …
  7. Thermostat Forgets Programmed Settings. …
  8. Thermostat Replacement Services.


Why does my furnace kick on so much?

The wiring could be old and need replacing, it might need new batteries, or it could be the location of your thermostat. If your thermostat is placed close to a heat source such as direct sunlight or a heat register, it will skew the temperature reading causing the thermostat to turn on and off irregularly.

Why does my furnace run every 5 minutes?

Blocked Exhaust Vent



This is another cause of a furnace overheating and short cycling. Short cycle time: 1-5 minutes. This issue can be dangerous too, since deadly carbon monoxide is dispersed through the vent. If it is blocked, the gas won’t escape, and it can leak out of the furnace and into your home.

How do I recalibrate my Honeywell thermostat?

Resetting a Honeywell Thermostat

  1. Power off the thermostat and remove the batteries.
  2. Put the batteries in the wrong way, with negative to positive and positive to negative.
  3. Wait ten seconds and put them back in the correct way.
  4. Your thermostat will be reset to factory settings.


What does resetting a thermostat do?

It will turn the thermostat off, and in most cases, it will restore the thermostat to factory settings. If you’re experiencing problems with your HVAC system, you should try using the reset button. If that doesn’t work, you can always contact an HVAC technician for assistance.

How do I fix an unresponsive Honeywell thermostat?

How to Troubleshoot A Faulty Honeywell Thermostat

  1. Disconnect all the wires connected to the thermostat. …
  2. Remove the device from the wall plate.
  3. Remove the batteries and wait for five minutes.
  4. Replace the batteries and reconnect the wires.
  5. Turn on the system and wait for five minutes.


How do you know if your home thermostat needs to be replaced?

9 Signs It’s Time to Replace Your Thermostat

  1. Your Thermostat Is Analog. …
  2. Your Thermostat Isn’t Programmable. …
  3. Your Thermostat Is Older than Ten Years. …
  4. Your HVAC Turns On and Off. …
  5. Your Energy Bills Are Unusually High. …
  6. Your Thermostat Gives Faulty Readings. …
  7. Your Thermostat Doesn’t Respond to Settings Changes.

How do I test my furnace thermostat?

How to Test Your Furnace Thermostat

  1. Step 1: Reset the thermostat lower or higher. …
  2. Step 2: Make sure the thermostat is ON. …
  3. Step 3: Check the wiring. …
  4. Step 4: Turn breaker back on. …
  5. Step 5: Reexamine wires. …
  6. Step 6: Wrap wires together.


How do you check if a thermostat is working?

Quote from the video:
Quote from Youtube video: Wait for the system to cycle you should hear click and then you should hear your cooling system come on and you should hear your air flowing. So as long as you do that.

Do furnace thermostats go bad?

Thermostats don’t typically have a set lifespan for maintenance, repair, or replacement (unlike air conditioners that need a tune-up every year). Still, you can generally expect your thermostat to last at least 10 years. After a decade, thermostats may start malfunctioning.

Is it my thermostat or furnace?

The thermostat should emit a clicking sound and the furnace should also make a sound. If the furnace does not make a sound, the thermostat is not sending a signal and needs to be replaced.