I would simply place a 1/4″ shim between the shower and the stud. This will allow you to screw the shower to the stud without cracking the shower. You may need another thinner shim on the stud about halfway up from the shower so your drywall doesn’t crack when you screw it down.

How do you fill gap between shower and wall?

Fill gaps up to 1/4 inch in width with caulk. If you have tile on the wall adjoining the tub, select a caulk that matches the color of the grout. If your gap is smaller than 1/8 inch in width, use regular caulk; fill gaps larger than 1/8 inch with a sanded caulk.

How do you fill the gap between shower surround and drywall?

Quote from the video:
Quote from Youtube video: Everything needs something to bond to mix up some 20-minute speed set joint compound. And press it into the gap keeping it flush with the drywall.

Can a direct to stud shower surround be installed over drywall?

The short answer to the question is, “It’s not recommended.” However, this answer only really only suffices if you’re converting a room that was never a bathroom into a wet space. Drywall on its own is not suitable for use in bathrooms because it is prone to absorbing moisture and thus losing structural integrity.

How do you frame a walk in shower?

Quote from the video:
Quote from Youtube video: What you need to do first is dry fit it over top your wood subfloor. That's what steve is doing right here he's going to mark out the position. Using a pencil.

How do you seal a gap in a shower?

You can quickly and inexpensively seal the shower with a caulking gun and a tube of caulk. The shower must be clean and dry, because caulk won’t adhere to dirt or water. There are many types of caulk available, so be sure to use the right caulk for the job.

How big of a gap can I fill with caulk?

A single bead of caulk can fill gaps up to 1/4 inch. If the gap is slightly larger than this, fill it with a bead of caulk deeper into the gap, but not flush with the surface. Wait until the caulk is completely cured before coming back to put a surface bead on.

How do you trim around a shower?

Quote from the video:
Quote from Youtube video: So we'll start off by nailing the luan or underlayment strips into the wall covering the flange be sure the strips are long enough to cover the flange. Now measure the back wall.

What do you do with a gap between tub and cement board?

The best approach when installing cement board or other tile backer around a tub is to keep the cement board out of the lip area. Apply it to the wall with the bottom edge about 1/4 in. above the lip of the tub. Then apply a generous amount of thin-set to the bottom bathtub tile and position it 1/8 in.

How do you waterproof drywall in a shower?

It is possible to waterproof drywall in a shower by covering the drywall with a waterproof membrane. This waterproof membrane can be bonded to drywall with thinset adhesive to create a waterproof layer. Never tile directly over drywall in a shower.

How do you install a stand up shower?

Quote from the video:
Quote from Youtube video: Once the mortar has set up you can cut the pvc drain to the exact height by using a special drill attachment that cuts on the inside of the pipe. Then just add the rubber gasket tighten the brass nut.

How do you build a walk in shower on a wood floor?

Quote from the video:
Quote from Youtube video: We're gonna start measuring down from the top of the subfloor to the height that we want the sister floor joists to be in this case it's the thickness of our Pam.

How do you frame a shower wall?

Basic Framing

The basic rules of framing apply to shower walls in regard to spacing. Wall studs should be 16 inches apart from each other, measuring center to center. In some remodel jobs, you’ll come across non-load-bearing walls that have as much as 24 inches between them.

What do I need to rough in a shower?

Quote from the video:
Quote from Youtube video: Your mixer valve and your tub spout and includes the mixer. Sometimes they don't include these they're just just the finished trims.

How do you frame a shower tub?

Quote from the video:
Quote from Youtube video: Before framing it now most most bathtubs are 5 foot wide that's your average bathtub.

How do you frame a one piece tub shower?

Quote from the video:
Quote from Youtube video: And typically in most tubs that thicker parts gonna go to the top and the thinner parts at the bottom. But get this into place right away get it snug don't over tighten them.

How do you install a direct stud shower surround?


  1. Prepare the Walls. Unless the studs are already exposed, installation starts by stripping the walls down to the studs around where the surround will sit. …
  2. Install the Back Wall Panel. …
  3. Install the Side Wall Panels. …
  4. Prepare the Front Wall Panel. …
  5. Install the Front Wall Panel. …
  6. Complete the Installation.

How do you find a stud in a fiberglass shower?

How to Find Studs Through a Fiberglass Shower

  1. Use a stud finder to locate a stud on any wall that is drywalled in your shower room by placing the stud finder up to the wall, turning it on, and moving it slowly until it beeps. …
  2. Measure the distance between the marks, center of stud to center of stud.

What can I use for a tub surround?

Bathroom remodeling contractors share four of the most popular materials that you can use for your bath and shower surrounds.

  1. Acrylic. Acrylic materials are cut from a large piece to fit every corner of your shower walls. …
  2. Ceramic and porcelain tiles. …
  3. 3 Glass tiles. …
  4. Stone tiles.

Should I put drywall behind tub surround?

Fiberglass and acrylic tub and shower enclosures come with a flanged edge that attaches directly to the wall studs, and the proper way to hide this flange is to install drywall over it. Consequently, enclosures are typically installed on the bare studs.

What should I put around my shower walls?

Simply put, acrylic panels have the look and style of tiles but without the mold, moisture, and cracking problems. A completely non-porous and waterproof material, it can be used to cover a full wall or as a decorative wainscoting wall accent. Acrylic is one of the most cost-effective materials for your bathroom.