The orange flame of your water heater indicates that the gas is not combusting efficiently, and it’s a sure sign that your heater needs adjustment or repair. This is also a safety concern because it usually means more soot (and possibly carbon monoxide) than normal is being produced by the burner each time it is used.

How do I fix the orange flame on my water heater?

How to solve yellow or orange flames

  1. Remove the scale from the top of the gas burner.
  2. Ventilation can very well be the issue, give your water heater proper ventilation and sufficient air.
  3. If the flue or vent system is blocked, make sure to find the cause, clean the pipes and remove the blockage.

Why is my hot water heater flame orange?





Orange – Orange flame is usually dust or dirt being burnt. Yellow – Air is not getting to the flame, this needs to be inspected immediately. An adequate supply of combustion and ventilating air must be available without obstructions.

How do you fix a orange flame on a gas heater?

Quote from the video:
Quote from Youtube video: Range make sure the burner portholes are clean and free of debris spill overs and cooking grease and block these openings which can affect the flame color.

Why is the flame on my burner orange?

A gas flame appearing yellow or orange in color or behaving with pops of yellow or orange indicates an improper ratio of oxygen for combustion. Often this improper combustion is temporary and could be caused by dust particles or a dirty burner that needs cleaning.

What color should flame be on hot water tank?

The correct flame color should be a light blue with the minimum of yellow tips. Incorrect flame color is yellow or sharp blue orange. If you see the burner flame color is yellow and lazy do the following: Provide sufficient fresh air to the water heater, especially if the unit is installed in the confined area.

How do you adjust the flame on a gas water heater?





Quote from the video:
Quote from Youtube video: All you have to do is loosen this nut or that that screw right there that that screw. Right there and adjust this piece right here which mixes the gas in the air.

What is the best setting for a gas water heater?

Know the Ideal Setting: The best setting for gas water heaters is around 115 to 120 degrees Fahrenheit. Oftentimes, water heaters will have additional options to either lower or increase the temperature of the water inside.

What color should a pilot light flame be?

bright blue color

Inspecting a Gas Furnace Pilot Light Flame



A natural gas flame should be a bright blue color with a small amount of yellow at the very tip. A propane flame will have more of a bluish-green flame with a tinge of yellow at the tip. The flame should strong enough to cover about 1/2 inch at the end of the thermocouple tip.

Is orange flame safe?



Orange, red or yellow flames can be very serious and harmful as it is formed due to improper work of the gas stove. The carbon monoxide (CO) that it releases is poisonous and can cause severe health problems.

What is the difference between a yellow gas flame and an orange gas flame?

There is a yellow flame. Carbon monoxide is produced. The burning of dust is represented by the orange flame.

Does orange flame mean carbon monoxide?

If you see orange flames instead of blue flames, the burners may need cleaning or adjusting. The orange color alerts you to your gas stove’s improper combustion, which may emit unsafe levels of carbon monoxide gas.

How big should a pilot light flame be on water heater?



about 1/2 inch

A pilot flame should be blue with a yellow tip and strong enough to cover about 1/2 inch at the end of the thermocouple tip.

How high should a water heater flame be?

about 1/2 inch

The pilot light and burner adjustment are key to proper and energy-efficient operation of the water heater. The gas flames should about 1/2 inch in height and should have blue tips (yellow flames indicate dirty burner jets or an improper air mixture).

Why is my water heater shooting flames?



Causes of Water Heater Flame Roll-Out



A clogged or damaged burner. A lack of combustion air. Incorrect vent pipe sizing, routing or termination. A blockage in the vent pipe.

How do you know if your water heater is going to explode?

The signs your water heater is going to explode are leaking tank water, the faulty pressure relief valve, cloudy water, popping noise, and the lack of hot water. A hot water heater explosion can lead to death, physical injury, and serious damage.

Should I see a flame in my water heater?

A flame that’s a steady blue cone is a sign that everything’s fine. However, if the flame is orange or yellow, and waving, then it’s burning up dirt and other pollutants. At that point, the flame isn’t warm enough to heat things properly. And, it’s more likely to burn out.

Can hot water tanks explode?

While rare, residential water heater explosions do occur and can be deadly. Explosions are possible with both gas and electric tank water heaters, primarily those that are poorly maintained.

Can a hot water heater catch on fire?



Yes, a water heater can cause a fire. Proper maintenance and safety precautions can drastically decrease the risk of a fire. Don’t store flammable materials or liquids near a gas water heater. There are many nuances and differences between different types of water heaters when it comes to fire safety.

How common is it for a hot water heater to explode?

Water heater explosions are rare but when they do happen, they can be devastating. Do not wait for a catastrophe. Here are a few signs your water heater will give before going burst. The pressure relief valve is usually located at the top of heater, on the side.