How do I put my GE front load washer into service mode?
Quote from the video:
Quote from Youtube video: To begin put the machine in standby mode by pressing the power button then disconnect power to the machine for at least 30 seconds.
How do you put a GE washer in test mode?
Test Mode is initiated by pressing a sequence of buttons on the washer’s control panel.
- Press the “Power” button on your GE washer. …
- Unplug the power cord for at least 30 seconds.
- Plug the power cord back in to the GE washer. …
- Press “Delay Start” to advance to “t02”.
How do I reset my GE front load washer?
To reset the electronic controls on your washer, shut off the circuit breaker or fuse to the washer or unplug the washer for 2 minutes. For models that have a timer control knob, turn the knob around and back to any position other than final spin for the interrupted cycle. Then, restore power.
How do you put a washing machine in diagnostic mode?
Quote from the video:
Quote from Youtube video: You press the start button this will allow your washing machine to go into the test or diagnostic mode and this will isolate if you're having any issues the water will run the spin cycle will engage.
How do I put my GE dryer in diagnostic mode?
Quote from the video:
Quote from Youtube video: Reconnect power and within 30 seconds of doing so press the following sequence signal delay start signal delay start on the control panel to enter the service mode.
How do I put my GE dishwasher in service mode?
Quote from the video:
Quote from Youtube video: So if the dishwasher in standby mode cycle selection model and look for this one here press. And hold the cycle select and start simultaneously for five seconds. Start and select cycle.
How do I reprogram my GE washing machine?
Motor Reset Procedure:
Unplug the washer for 1 minute from the electrical outlet. Plug the washer back in and lift and lower the lid 6 times within a 12 second period. You have 30 seconds to start lifting and lowering the lid.
How do I troubleshoot my GE washer?
How to Troubleshoot a GE Top Load Washer
- Check the amount of detergent you have put in the washer. …
- Examine the GE top load washer’s drain hose for leaks. …
- Check the water connections to your GE top load washer. …
- Check whether the GE top load washer lid is closing firmly. …
- Check the load in your GE top loading washer.
How do you clear the error code on a GE washing machine?
To clear and verify a GE washing machine error:
- Press and hold the “Power” button until the error clears.
- Unplug the washing machine from its power source.
- Wait at least three minutes.
- Plug the washing machine back into the power.
- Allow the washer to reboot.
- Attempt to run a wash cycle.
How do I put my Whirlpool front load washer in diagnostic mode?
Quote from the video:
Quote from Youtube video: Choose any three buttons except for power or start and press them in sequence. One. Two three one two three one two three. If you got it right you'll know the duet washer has three diagnostic modes.
How do I put my LG washer in diagnostic mode?
Press the POWER to turn on the washer. Place the mouthpiece of your phone between the Smart Diagnosis logo and the POWER button. After pressing the Start Diagnosis button, press and hold the TEMP button until a countdown displays on the washer.
How do you put a Kenmore front load washer in diagnostic mode?
3 Answers
- With the washer empty, close the door.
- Push “control/on” or “Start”
- Select “Drain/Spin”
- Select “No Spin” by pressing SPIN SPEED touchpad.
- Push “PREWASH” option four times within 5 seconds. (If there is no PREWASH option, press RINSE HOLD 4 times in 5 seconds.)
- C:00 should light up and begin the diagnostic.
How do I reset my GE front load dryer?
How do you reset a GE dryer? Turn the dryer off, then on again to reset it. Or you can press the reset button on the dryer plug.
How dO I know if my thermal fuse is blown?
To test if your thermal fuse has blown, touch the right side of your multimeter lead to the right side of the fuse, and repeat with the left multimeter lead. If the multimeter needle fails to move, this indicates the thermal fuse has blown. Learn about testing for a blown fuse.
How do I troubleshoot my GE dryer?
Quote from the video:
Quote from Youtube video: One of the most common problems of a dryer is that it doesn't dry well or it doesn't dry. At all in here you want to check may seem obvious. But you want to check the lint trap.
How do I reset my thermal fuse?
Quote from the video:
Quote from Youtube video: So if you have this issue and you keep spot or you trip this you may want to try drilling this. And then you got a little bit of pressure. And it resets. It. So if you're testing your dryer.
Where is the thermal fuse?
Quote from the video:
Quote from Youtube video: Location of the thermal fuse is right on the blower housing.
Where is the thermal switch?
Thermal switches are used in power supplies in case of overload, and also as thermostats, and overheat protection in some heating and cooling systems. They are found in virtually every refrigerator, microwave, clothes dryer, space heater, and many more appliances found throughout the home.
