Why won’t my GE Profile dispense water?

On models with a water filter, a clogged or partially clogged filter will result in no water or slow running water from the refrigerator dispenser. Please change the filter. We recommend replacing the water filter every 6 months.

How do you reset a GE Profile water dispenser?





GE Profile Filter Reset



The water filter warning light or message is reset by pressing the Ice & Water pad on the control panel for three seconds. The filter light should turn green, and the filter status will show Good.

How do I fix my GE refrigerator water dispenser?

Quote from the video:
Quote from Youtube video: If you have the pin style. Then you can put a towel down take the filter out. And use a couple small screwdrivers to press them. In. Then press the dispenser.

Why is water not coming out of refrigerator water dispenser?

Water can stop flowing from the fridge dispenser when supply lines become frozen, clogged, or kinked. Some water lines run through the freezer, so if the temperature is set too low, the water line will become frozen. If there is ice in the line, allow it to defrost.
Jun 15, 2021

Why is my GE refrigerator not dispensing water or ice?

If you discover your GE refrigerator not dispensing water or ice, the dispenser switch may have failed. No voltage, no working dispenser. A multimeter can be used to check for continuity to determine if the dispenser switch is working properly. If there is no continuity, then the switch needs to be replaced.
Jun 3, 2019

Why is my GE refrigerator water dispenser not working after replacing filter?





Check that the threaded area where the filter will connect to the refrigerator has nothing blocking the small holes where the water will flow through. Sometimes part of the wrapping on the new filter itself could possibly block the water flow. If something is blocking flow, this will cause low flow.
Oct 12, 2015

How do I reset my water dispenser?

Option 3 – Try “resetting” your cooler by removing several cups of water from both the hot and cold taps and switch off the machine. Unplug it from the wall and leave for 24 hours before switching it on again. Give the water temperature about 5 to 6 hours to adjust before dispensing to see if it worked.
Dec 2, 2009

How do I fix my water dispenser?

Quote from the video:
Quote from Youtube video: So on the back end of most cooler units you're gonna have like this little thin grill mine has screw here and another one on the bottom.

How do I reset my GE Profile refrigerator?

When “0” flashes in the displays, the refrigerator is in the self-diagnostic mode. Press “1” and then “5” to completely reset the entire system. After the system resets, unplug the refrigerator and then restore power. The refrigerator is now reset.

Why does my ice maker work but not the water dispenser?



Frozen Tank or Tubing: The water reservoir tank or tubing could be frozen. If frozen, you would get water to the icemaker but not the dispenser. The water reservoir tank or tubing is typically located behind the vegetable drawers or on the left side of the fresh food compartment.

How do you know if your refrigerator water valve is bad?

The cubes may be small or there may be a solid chunk of ice instead of individual cubes. It’s also possible that the icemaker will stop working. These are all signs of a malfunctioning water valve.
Jan 1, 1999

How do you know if your refrigerator water line is frozen?

Quote from the video:
Quote from Youtube video: So if you can see up there the little tube the little tube is what the water comes out of and if you look really closely you can see ice has built up in that tube.

Why does my fridge say dispenser off?



If there is a leak detected, the dispenser will shut off. This would require a service call to correct.

How do I clean my GE Profile refrigerator water dispenser?

To remove deposits:

  1. Soak the area with one of the following solutions: Undiluted vinegar. A mixture of 1 teaspoon of citric acid powder and 1 pint of hot tap water. …
  2. Soak until the deposit disappears or becomes loose enough to wipe away. Usually, 30 minutes of soaking time is adequate.


How do I reset my GE Rpwfe filter?

The “Water Filter: Replace” status message can be reset by entering the Settings menu from the home screen. Then, select the Water Filter menu and press the RESET button. This will reset the filter status.

How do you know if your refrigerator water line is frozen?



Quote from the video:
Quote from Youtube video: So if you can see up there the little tube the little tube is what the water comes out of and if you look really closely you can see ice has built up in that tube.

How do you reset a refrigerator after changing water filter?

Quote from the video:
Quote from Youtube video: Holdfast cool and energy saver at the same time for three seconds. And your filter is reset.

Why is my filter light still red?

Red: This indicates that the filter needs to be changed. You can almost always get a full six months out of your filter. Red does not mean you can no longer use the filter or that your water is not being filtered. It just means you should change it as soon as possible.
Jan 19, 2018

What does red on water filter mean?

Red [indicates] the filter has reached 100% of its usable life and should be replaced promptly.” Many students are concerned with drinking the water when the filter is red and some even avoid filling up at stations displaying the red light.
Apr 11, 2019

How does my refrigerator know when to change the water filter?



The Indicator Light



Most new fridges feature an icon that lights up and notifies you when it may be time to change your water filter. Many of them are set to turn on after a certain amount of time; however, some newer models know how to check the actual status of the filter and only turn on when the filter is dirty.
Sep 30, 2017