Right off the top, “motor or control” + “fills” + “one or two rotations” + “drains” indicates a problem with the drum motor. Since it fills and drains, it is unlikely to be related to hoses, filters, inlet valve, etc. These three errors are motor errors and can be caused by a bad inverter or motor.
Why is my washing machine filling up and then draining?
If your washer continues to fill during a drain cycle, the water inlet valve could be at fault. To verify that the valve is at fault, unplug the washer when the symptom occurs. If the washer continues to fill, then the inlet valve is defective.
Why does my washer keep draining?
Your washer may have a clogged drain hose or the pump may be broken. A broken lid switch or belt could also be the culprit. It may even be something as simple as the hose being jammed. Whatever the reason, the water will need to be drained from the washing machine before any work or diagnosis can be done.
Why is my GE washer not holding water?
A kink or clog in your washing machine’s drain hose could be interfering with water flow and preventing your machine from draining properly. To inspect the drain hose, turn off the power to the washer, disconnect the hose (have a bucket ready to catch any water), and check the hose for damage or obstructions.
Why does my GE washer keep shutting off?
Common solutions for: GE Washer stops mid cycle
If the door lock is defective, the washer may stop mid cycle. The door lock can fail either mechanically or electrically. Inspect the door lock for damage. If the door lock is damaged or does not latch properly, replace it.
How do I reset my washing machine?
Quote from Youtube video: The machine gives you 30 seconds to lift the lid and close. It six times and once you start lifting the lid. You have 12 seconds to do the six repetitions.
What is washing machine siphoning?
Siphoning means the washer will fill and drain at the same time. This happens when the drain height is too low. Siphoning can also occur if the drain hose is pushed too far down into the drain pipe. For new Top Load washers, the drain hose should be no more than 5″ down into the drain pipe.
Why does my washing machine stop after a few minutes?
Possible Causes
One common issue that can cause a washing machine’s cycle to stop is the heater to stop working properly. To test this set your washer on a cycle and monitor it every so often, if the cycle stops within the first 30 minutes then the water likely isn’t getting sufficiently heated.
How do you reset a GE washing machine?
Motor Reset Procedure:
- Unplug the washer for 1 minute from the electrical outlet.
- Plug the washer back in and lift and lower the lid 6 times within a 12 second period. You have 30 seconds to start lifting and lowering the lid. …
- The motor has now been reset and is ready for you to start a cycle.
Why does my GE washer stop mid cycle?
A door lock error will cause the washer to stop mid-cycle. Begin by inspecting the door to check for a secure fit. Wiggle the handle, and see if the door can be jostled while closed. Check the door lock switch to see if anything is obstructing it, or preventing it from pressing down securely.
How do you troubleshoot a GE washing machine?
How to Troubleshoot a GE Top Load Washer
- Check the amount of detergent you have put in the washer. …
- Examine the GE top load washer’s drain hose for leaks. …
- Check the water connections to your GE top load washer. …
- Check whether the GE top load washer lid is closing firmly. …
- Check the load in your GE top loading washer.
Where is the reset button on my washing machine?
Some machines have a button you push to reset its motor. On a machine without a reset button, unplugging the washer and then plugging it back in often serves as the means to reset it. Although not usually a button, programmable washing machines might have a reset function or position to clear a program problem.
How long does it take for washing machine to reset?
If you see no change, you can try a Master Reset. This will reset all of the onboard componentry and is often successfully used by appliance technicians. Open and close the door of the washing machine 6 times within 12 seconds.
Can you reset your washer by unplugging it?
To reset your washing machine, unplug it from the power outlet. Then, plug the washer cord back into the wall. Finally, open and close the washing machine door six times to send the reset signal to the system components.
What are common problems with washing machines?
10 Most Common Washing Machine Problems
- It Bounces Around. …
- It’s Noisy. …
- Clothes Are Getting Ripped. …
- Improper Or Slow Draining. …
- My Washing Machine Won’t Spin. …
- There’s No Water. …
- The Door Won’t Open. …
- It’s Smelly.
