Use a fine-toothed metal-cutting blade and don’t force it. They’ll zip off in under a minute. If you find that you can’t get your cut low enough, go as low as you can, then make two opposing vertical cuts down the center from the top. Whack the quarters outward with a heavy hammer so they’re below grade.
How do you remove a post from a clothing line?
Dig around the cement base with a shovel. If your pole doesn’t have a cement base, dig around the pole until you’re able to lean against the pole, working it loose. You can then remove the pole.
How do you remove a metal pole from the ground?
Quote from the video:
Quote from Youtube video: Once you've got enough stuff dug up and you can drill some holes drill some holes. Again. Be safe if you've never drilled metal before it might very well be difficult.
How do you remove a clothesline from the ground?
Step by step:
- Get some warm soapy water.
- Undo the locking cap and pour warm soapy water into the ground socket hole.
- Rock the stem of the Hills rotary clothesline, to get water around the pole.
- Wait approximately five minutes, then try guiding the rotary clothesline out of the ground socket.
What are clothesline poles made of?
steel pipe
Clothesline poles were the first product created and sold by Donald Agar in the early 1990’s. We still proudly build them today. Our clothesline poles are 8 feet high, 4 feet wide, and are made from 2 1/2″ (outside diameter) steel pipe.
How do you cut steel posts?
Quote from the video:
Quote from Youtube video: Hiya Jim I'm Aiman and this is the Hercules angle grinder. So easiness to cut this post here because it's blocking or password or wheelbarrow to go through.
How do you get a metal pole out of concrete?
Use the Jack for Removing Steel Fence Posts
Put the end of the chain on the jack tongue and crank the jack. Keep a close eye on the chain to ensure that it doesn’t slip or move. Once you lift the pole and slab enough, you should have someone help you lift them out of the ground and carry them away.
How do you make a clothesline pole?
Quote from the video:
Quote from Youtube video: And then I'm going to square. Across. Now I'm going to take the cross piece. And line it there line it across that square mark put a line and I'll cut that out with the circular.
How deep should a clothesline pole be?
about 12″ – 18″ deep
Make the holes about 12″ – 18″ deep and 12″ wide. The bottom of the hole should be slightly wider than the top — this helps prevent any movement when the earth settles. Note: Pole height can vary a bit depending on how high you want your clothesline to be.
How do you install a metal clothesline pole?
Quote from the video:
Quote from Youtube video: You also need some concrete for the to hold the the clothesline in place. And we also need some gravel which needs to go into the bottom of the hole to provide for drainage.
How do you cut a metal pole without a saw?
Quote from the video:
Quote from Youtube video: So here's it's just a little abrasive cutting wheel little 4 inch 4 inch it'll fit on the 4 and a half or for each grinder. They also come in 7 inch. That will not only fit on the bigger grinders.
How do you cut galvanized poles?
Quote from the video:
Quote from Youtube video: Make sure you don't cut the the wire for your power tool i think once you get most of the way done you're able to kind of break off the post with a little effort.
How do you cut a stainless steel pole?
Quote from the video:
Quote from Youtube video: And made them easier to cut this hard material stainless is a real tough animal. So you need something that's up to the job. So we've got two very nice little tube cutters here the 35s. And the 65s.
What can I cut stainless steel rod with?
Cutting Stainless Steel Sheets. Use a circular saw. A circular saw is a handheld power saw with a circular blade. You can quickly cut through stainless steel with a circular saw if you use the right blade.
How do you cut thin steel rods?
Cut Metal with Your Circular Saw
It may not be an obvious choice, but fitted with the right blade, a circular saw is a great metal-cutting tool. In our test, it cut through rebar like a hot knife through butter. You can cut mild steel up to about 3/8 in. thick using a ferrous-metal-cutting blade.
Can I cut stainless steel rod with a hacksaw?
A hacksaw will do fine but an angle grinder would be a lot quicker!
How do you cut metal threaded rods?
Quote from the video:
Quote from Youtube video: Rod you spin that well past where you want to cut the rod. At that point you can either use a hacksaw. An angle grinder reciprocating so whatever you want whatever you want to cut the threaded rod.
How do you cut stainless steel without burning it?
Quote from the video:
Quote from Youtube video: This hardness creates friction and the friction creates heat and as soon as the cutting edge of your tool gets glowing red-hot from the friction. It starts to melt down.
