Most motion detectors have a built-in override:

  1. Normally the switch is kept on all the time. …
  2. If you turn the switch off and on within a second or so, the light will stay on, and this overrides motion detection.
  3. To go back to normal operation, turn the switch off and wait ~10 seconds, then turn back on.

How do you manually override a motion sensor light?

Yes, most sensors will have the ability to override the sensor function altogether and operate the light manually, as necessary. This is done by turning the light switch OFF – ON – OFF – ON in quick succession. The light will then remain ON and will not go OFF until you manually turn it OFF at the switch.

Can I bypass the motion sensor on outdoor light?

Many motion detectors can be bypassed with little effort. With an additional light switch, the connected outdoor light can then be switched to permanent light.

Can you disable a motion sensor light?

Most manufacturers make it a fairly easy process to disable this main feature of the lights. A switch on the fixture should read “on time,” usually found directly under the motion sensor. Set it to any position, aside from the test position, and flip off the switch that the light is connected to.

How do you bypass a motion detector?

Quote from the video:
Quote from Youtube video: I've got the ground line hooked up here this is just bare copper wire. And the white neutral. And then the black power coming in norm in the normal mode of operation.

Can you cover a motion sensor?

A quick solution that customers have said works well is to use black electrical tape to cover part of the sensor. Start by covering the edge of the sensor on the side you want to keep out of the detection area and use small pieces of tape to block it out.

Can a motion light be controlled by a switch?

If you use a motion sensor, this can act as a switch, controlling when the light goes on and off. However, there might be times when you’d like to stop the light from responding to the motion. If you want to stop the light from switching on every time anybody walks past, you can use a switch to stop it from working.

How do I bypass dusk to dawn sensor?

To disable the dusk-to-dawn sensor (D), you will need to install the sensor cap (CC) over the dusk-to-dawn sensor (D) (Fig. 2). This will prevent the dusk-to-dawn sensor (D) from controlling the ON/OFF function, and should allow you to control the fixture (A) with the wall switch. 1.

What is a photocell resistor?

A photocell is a resistor that changes resistance depending on the amount of light incident on it. A photocell operates on semiconductor photoconductivity: the energy of photons hitting the semiconductor frees electrons to flow, decreasing the resistance.

How do I find the image switch?

Touch the red probe of the meter to the red wire of the sensor and the black probe of the meter to the sensor’s black wire. Wave your hand back and forth in front of the sensor. If the photocell sensor is working properly the switch will activate and the needle on the meter will move upward.

What is a photocell shorting cap?

The shorting cap provides a closed circuit when a photo control is not installed, keeping lights continually on for safety. An open cap disconnects service when lighting is no longer needed.

How do you test a photocell sensor?

The easiest way to determine how your photocell works is to connect a multimeter in resistance-measurement mode to the two leads and see how the resistance changes when shading the sensor with your hand, turning off lights, etc. Because the resistance changes a lot, an auto-ranging meter works well here.

How can you tell if a photocell is bad?

Security Light Photocell Problems

  1. Extraneous Light. The most common problem encountered with security lights controlled by photocells is that they shut off unexpectedly during the night. …
  2. Dust and Shading. Another problem with security lighting is that the light remains on during the day. …
  3. Electrical. …
  4. Incorrect Settings.

How do I reset my photocell light?

How to Reset the Light Sensor on Outdoor Lights

  1. Flip off the light switch that powers the outdoor lights.
  2. Leave the light switch off for one second.
  3. Turn the light switch back on to reset the light sensors to auto.