How do I move my shower supply line?

How to Move a Plumbing Fixture in the Shower

  1. Turn off the watter supply to the house, then open all faucets to drain as much water out of the system as possible.
  2. Remove the tubing straps securing the shower valve to the framing.
  3. Cut the all the pipes coming to and from the existing shower valve.

How do you install a shower pipe in the wall?





Quote from the video:
Quote from Youtube video: Again pop some jointing compound on there pop some jointing compound on the inside of the brass fitting as well just run it around with my finger. And then i'll re-tighten. Up that fitting.

How do you brace shower plumbing?

Quote from the video:
Quote from Youtube video: We've applied a little caulking to the back side of the plate for a watertight seal.

How do I move a shower plumbing to the opposite wall?

All you need to do is run the hot and cold water supply lines to the end of the shower opposite the shower head. The shower control can be mounted wherever you would like it in that wall. Then a single line can be installed from the shower control to the shower head.

Can you relocate a shower?

When moving a shower, you’ll also need to install the shower head in the new location. You can either have your current shower head reinstalled or choose a brand new one. If you have an older showerhead, switching to a new one during this renovation is typically a better option.

Is it difficult to relocate a shower?





Showers. Moving a shower is a little tricky and expensive since it involves moving the pipes in the wall and the floor. You also have to consider the drainage system and your shower system.

Can you put pipes in the wall?

The process of chasing pipes into a wall isn’t too complicated but does need to be done with care to avoid any accidents. Damaged pipes will cause leaks with potentially disastrous consequences. Whether it’s for pipework or electrical conduit, the method of chasing is the same.

How do I build a shower partition wall?

Quote from the video:
Quote from Youtube video: Create a modular connection at the wall to pan transition. This notch will be 1/2 inch by the remaining thickness of the pan excluding the pans rabbet channel this is to ensure a strong connection.

Can you put a shower on a stud wall?

Your stud wall will probably be ok but it would be nice to get one of the fixing screws in one of the studs. Otherwise something like a spring toggle clip should spread the load. Make sure you silicone between the valve/rail and tiles to improve adhesion and try to use brass or stainless steel screws.

How do I move plumbing walls?



Quote from the video:
Quote from Youtube video: And it wasn't wall-mounted. So new thing that people are doing is the wall mounted vanity. I'm also gonna have to move that drain in the wall. But same concept same thing that I'm going to do here.

How do I change the location of my shower head?

Quote from the video:
Quote from Youtube video: Head first wrap thread seal tape in a clockwise. Direction two or three times around the threads of the shower arm. Press the tape into the threads.

How do I extend my shower head pipe?

Quote from the video:
Quote from Youtube video: Version you can simply screw the nut in a clockwise. Direction by hand first and then tighten it with a pair of pliers. But i have to rotate the whole unit as one.

How do I extend my shower head from the wall?



The easiest and most affordable way to raise the height of your shower head is with an adjustable shower arm. This type of shower arm attaches to your existing shower arm pipe, acting as an extension, and then you can attach your existing shower head.

How do you extend a shower?

The most critical aspect of enlarging your shower is replacing the shower pan, or the raised floor that collects all the water and ensures that it flows down into the drain. If you are an expert home project DIYer, you can build your own custom shower pan using concrete and a special membrane.

How do you install a shower extension?

Quote from the video:
Quote from Youtube video: One.

How far back should a shower valve sticks out from wall?

The center line of the supply and discharge piping should be a maximum of 2-3/16″ (56mm) and a minimum of 1-7/16″ (37mm) behind the finished wall surface.

How do you extend a tub pipe?



If your bathtub spout pipe is too short, then you can extend it two different ways. The first way is to weld a coupling and piece of extension pipe onto the spout pipe. The second method uses a pipe-fit plumbing fitting instead of a coupler and welding torch. They both have their advantages and disadvantages.

What is a shower valve?

A shower valve is found behind the handle of a shower faucet. It controls the temperature of the water and turns the shower on and off. Through a temperature mixing valve, the hot and cold lines are mixed together to create the desired temperature.

Where is a shower valve located?

You can see the trim on the shower faucet, but the actual valve is behind the wall and is permanently connected to the plumbing. To replace it, you need an access panel through the shower wall, and if it isn’t designed into your bathroom, you’ll have to cut one.

Which shower valve do I have?

If you want to know how to identify the shower valve manufacturer, check behind the shower handle at the center of the trim plate for the manufacturer’s symbol or brand name. You will see one of the following shower faucet logos: K: the manufacturer is Kohler. M: the manufacturer is Moen.