3 Answers
- Get a 2-gang box to replace your existing 1-gang box.
- Get a new switch.
- Remove your existing box and install the 2-gang box in its place.
- Run your supply hot wire to both switches.
- Connect the light/fan hot wire to one switch and the exterior light to the other.
- Join all neutrals and ground wires.
Can two lights be controlled by one switch?
The answer is yes; one switch can turn on multiple lights. You can use two ways to make your switch control multiple lights. The most common way is to daisy-chain the light fixtures through connecting them with each other and hooking the first fixture to the switch.
How do you make a single light switch into a double?
Quote from Youtube video: So what i did here is put some tape on the wall i take an old work double gang. Box. And i flip it upside down and basically i want to trace the remaining. Space on the wall. So i cover the hole.
How can I eliminate one 3 way switch to leave just one switch on the lighting circuit it’s on?
3 Answers
- replace that switch with a single-pole switch.
- connect either of the “traveler” wires to the load side.
- remove the other (unwanted) switch and connect the traveler wire used in step-2 to the “switched hot” wire that goes to the lights.
- the unused “traveler” wire is abandoned.
How do I control multiple outlets with one switch?
Simply plug a Switcheroo into your switched outlet, and then another Switcheroo into as many outlets that you want to turn on and off with your existing switch. Set them to the same channel and you are done. Or, use different channels for multiple configurations around your house.
How many lights can you have on one switch?
A regular 15A circuit can have up to 1400W of lights connected, or one 1400W light or 14 100W light bulbs. Most homes allow for 23 to 40 60-watt bulbs or 280 to 480 5-watt LEDs.
How do you wire a light switch for multiple lights?
Quote from the video:
Quote from Youtube video: The correct wire to use at the switch will be the wire coming from the second switch. The remaining two neutral wires one coming from the power source and the other from the light fixture.
How do you tap an existing wall switch?
Quote from the video:
Quote from Youtube video: You always want to grab a top and bottom loosen the screws. And then pull the switch all the way forward everything's been removed from the wall. And there's three screws on the switch.
Can a switch control multiple outlets?
If the switch is at the end of the run then you will need 3-conductor cable between the several outlets and between the outlets and the switch. Pass the hot through all the outlet boxes to the switch via the black wires.
How do you separate an outlet from a switch?
Quote from the video:
Quote from Youtube video: Side what you're going to do is you're going to take your needle nose pliers. And you're just going to take off this tab move this back and forth. And break it. Off. Each one of this is independent.
How do you wire a combo switch?
Quote from the video:
Quote from Youtube video: The two white wires from the power and the light fixture wire tie them together and I've also added a pigtail wire. Again a white wire with a loop at the end of it.
How do you daisy-chain lights together?
Quote from the video:
Quote from Youtube video: Cover you can just set it over the wires. And pop it in place. That's another way to just get out of some more work. We hope this is clarified some of the questions.
How do you wire multiple LED lights together?
Quote from the video:
Quote from Youtube video: Let's start off by taking a look at what it means to connect LEDs in a series connection in this basic setup the power is actually going to flow from positive to negative through each LED.
How do you wire a series of lights?
Quote from the video:
Quote from Youtube video: Now going from the first light box to the second light box is a 12 2 with ground going from the second light box to the third light box is a 12.2 with ground cable.
Should LED lights be wired in series or parallel?
series-parallel
Generally speaking, most LED lighting uses a series-parallel combination. Ideally, for reliability and lighting consistency, it would be best to have one strip of LEDs all wired in series to a constant current driver.
How do you split LED strip lights?
LED strip lights are designed to be easy to cut apart with a pair of scissors. Each LED has a pair of copper dots at the end. As long as you cut between the dots, all of the LEDs will work. From there, you can connect the LEDs to a power source either through a quick connector or by soldering.
Can you cut LED lights and they still work?
Will they continue to work if they are trimmed down? Yes, LED strip lights will carry on working after they’ve been cut as long as you cut along the designated lines. LED strips are made up of several individual circuits, so each cut line demarcates the end of one circuit and the start of a new one.
Can you use one remote for multiple LED lights?
You can control multiple strip lights with only one remote. If each LED strip has its own controller, you can sync all the controllers with one remote.
