How do you put a metal pole in the ground?
Quote from the video:
Quote from Youtube video: This is how I set them up while the concrete's drying got a 1 by 2 nail to 2×4 or actually a 4 by 4 and then another one going down there and then I just use a ratchet strap to hold them together.
Does galvanized pipe react with concrete?
Chemical reaction with galvanised steel
Tube reactions between galvanized reinforcement bars and concrete are only of concern during the initial curing stages of the concrete. The initial stages of curing include the time when the concrete mix is still wet.
How do you set a ground pole?
Quote from the video:
Quote from Youtube video: The ground men will fill the hole of dirt. And use a manual or hydraulic tamping iron to pack the dirt and firmly set the pole once the pole has been firmly set disconnect. The winch line remove.
How do you hang a concrete pole?
The most common method and biggest advantage for installing a concrete pole is by direct embedment. The pole is placed into an augured hole lined with gravel then back filled with native soils, stone dust or cement – depending on the soil conditions.
How deep does a pole need to be in the ground?
In fact, utility poles are buried according to a specific formula: 10% of the pole’s height plus two feet equals the appropriate depth of burial. A standard utility pole measures 40 feet, so a standard hole will go about 6 feet down into the ground.
How do I attach a metal pole to concrete?
Quote from the video:
Quote from Youtube video: Remove the base and then drill into the concrete using a hammer drill. And masonry drill bits. Move the post support back over the holes.
Can you pour concrete against galvanized steel?
Never, ever. Because? According to National Ready Mixed Concrete Association (www.nrmca.org), “For steel embedded in concrete, corrosion results in formation of rust which has two to four times the volume of the original steel and none of its good mechanical properties”.
Can you pour concrete on galvanized steel?
Can galvanized and black steel reinforcement be used together in concrete? Because zinc is naturally protective to steel, galvanized reinforcement can be safely mixed with uncoated in concrete.
Will concrete bond to galvanized steel?
The reaction of zinc with the concrete effectively ceases in a few days and gives just sufficient corrosion products to ensure a strong and reliable bond to the concrete when fully hardened. The bonding between galvanized rebar and concrete is essential for the reliable performance of concrete structures.
How deep do metal fence posts need to be?
As a general rule, Fencing Direct recommends at least a 24-inch footing depth for a 4-foot fence, plus an extra 3 inches for every foot of height (for example, 27 inches for a 5-foot post). The minimum hole diameter should measure four times the largest cross-section of the post.
How do you build a concrete base for a pole?
Quote from the video:
Quote from Youtube video: You're going to need cement a bowl pipe cap and hot glue gun. Hot glue the pipe cap to the bottom of the bowl mix up the concrete. And fill up the bowl.
Can you put dry concrete in a post hole?
Fast-setting concrete is ideal for setting posts because there’s no mixing—you simply pour the dry concrete from the bag right into the hole, then add water.
How deep do you bury a 20 foot pole?
Dig a hole in your lawn with a shovel where you want to install the flagpole. Make the hole 3 feet deep and 1 to 2 feet wide.
How deep should I bury a 20 foot post?
The general rule of thumb when setting a post is that the depth of the post’s hole needs to be one-third to one-half of the actual above-ground height of the post. So, a six-foot-high finished post ideally needs to be buried three feet into the ground.
How deep should an 8 foot post be in the ground?
about 2 feet deep
For an average fence post, about 6 to 8 feet tall, prepare to dig a post hole about 2 feet deep. To install a fence post, you’ll need a shovel or post digger, a 6-foot level, soil, and gravel or crushed stone.
How deep should a 6 foot post be in the ground?
The depth of the hole should be 1/3-1/2 the post height above ground (i.e., a 6-foot tall fence would require a hole depth of at least 2 feet). Add about 6 inches of QUIKRETE All-Purpose Gravel into the bottom of the hole. Then compact and level the gravel using a post or 2×4.
How much concrete do I need for a post hole?
Most fence post holes will need between 1 – 4 bags of concrete to securely hold the post in place. The best way to determine the size of the hole is: Diameter of the hole is 3 times the width of the fence post. Depth of the hole is one-third to half the above ground height of the fence post.
What size post do you use for an 8 foot fence?
A common rule of thumb, is to dig the hole 3 times as large as the post, and to a depth of 1/3-1/2 of the post height above ground. so for a 8′ high fence, using 4×4 posts. dig the holes 12″ in diameter, to a depth of 2 1/2 – 4′. Of course, that’s assuming you’re setting the posts in concrete.
How much concrete do I need for fence posts?
How Much Concrete For A 4×4 Fence Post?
| Depth | 50 Lb Bags |
|---|---|
| 10″-14″ | 2 |
| 16″-22″ | 3 |
| 24″30″ | 4 |
| 32″36″ | 5 |
How many feet apart should a fence post be?
8 to 12 feet
Most fence posts can be spaced 8 to 12 feet apart. While this is a general criteria, it doesn’t cover all scenarios. For instance, high tensile fence can have larger spacing, requiring line posts every 15 to 20 feet for field fence styles, and as much as 20-30 feet for high tensile barbed and smooth wire.
