How do you connect different size tubing?
Quote from the video:
Quote from Youtube video: This is a perma lock tubing T adapter. Two sides of the fitting can be attached to one-half inch poly tubing and the third side can be attached to three-quarter inch poly tubing.
How do you connect two plastic tubes?
Quote from the video:
Quote from Youtube video: I like to use the felt tip marker I not only give myself index marks but I number the joints too so it all goes back together without any confusion prime the pipe in the fitting.
How do you connect plastic tubing?
Quote from the video:
Quote from Youtube video: Let's put cement on the fitting and the PVC pipe and inside of both ends of the coupler. I'm going to put the coupler on the pipe. First little quarter turn for a good seal.
How do you connect a tube pipe?
Quote from the video:
Quote from Youtube video: Well just press the two end of the fitting. And you're done if you try to save a few cents and use a compression fitting. You need to unscrew the fitting. Then slip on the sleeve.
What is a tube Adaptor?
Pipe-to-tube adaptors
Pipe-to-Tube weld adaptors allow standard tubing components to be used in piping systems with a smooth transition between the pipe bore and tube ID. Machined from 316L stainless steel with wetted surfaces finished to 0.5 microns Ra.
What are tube adapters?
The port end allows the fitting to act as a bridge between the tube and the component. A fitting that has both a port end and a tube/hose end is commonly referred to as an adapter. An example of this would be connecting the tube directly to a pump.
How do you join plastic parts?
Hot plate welding joins two plastic parts by melting them against a precisely heated platen for a prescribed period of time. The platen is removed and the two parts are forced together. The resulting joint bond is strong, permanent, and often hermetic.
Do compression fittings work on plastic pipe?
A compression fitting works in the same way on a plastic pipe as it does on a copper pipe except that you need to put in a liner, which is there to keep the end of the pipe perfectly round.
How do you connect two pipes without threads?
Insert one end of the non-threaded galvanized pipe into the coupling. Align the coupling end with the drawn line on the pipe. Insert the second pipe into the coupling and center the coupling between the two drawn lines.
How do you install a tube connector?
Quote from the video:
Quote from Youtube video: At the six o'clock. Position along with the body with your marks at the six o'clock position we're going to continue to rotate this nut with a wrench one and one quarter turns from hand tight.
How do you use tube fittings?
Quote from the video:
Quote from Youtube video: Position. For one-sixteenth one-eighth and 3/16 inch and two three and four millimeter tube fittings tighten the nut only 3/4 turn to the three o'clock.
How do you install a compression fitting on a plastic tubing?
Quote from the video:
Quote from Youtube video: The sealing ring has got a tapered edge you must put the tapered edge towards the fitting. Bring the fitting in push-ups. At the tapered edge is squeezing onto the fitting.
How do you hook up a 1/4 compression fitting?
Quote from the video:
Quote from Youtube video: Slide the compression fitting onto the tube until the tube bottoms out a drop of lubricating oil or thread sealant will ease not assembly thread the nut onto the fitting hand-tighten.
How do you assemble a 1/4 compression fitting?
How to Install Compression Fittings on a 1/4 Water Line
- Slide the compression nut onto the ¼-inch water line. …
- Slide the compression ring onto the water line. …
- Connect the compression nut to the threaded male water intake compression seat. …
- Turn the water valve on.
Sep 26, 2017
How do you do a compression fitting?
Quote from the video:
Quote from Youtube video: Just place the pipe into the fitting. As far as it will go then slide your nut down over the olive. And tighten up by hand.
How does a plastic compression fitting work?
Quote from the video:
Quote from Youtube video: This up and as it tightens up it compresses that sleeve it's that little it's available in brass or plastic. And it compresses the sleeve. Into the top of that fitting. And that creates the seal.
How do you use a compression fitting ferrule?
Quote from the video:
Quote from Youtube video: The ferrule coins and compresses into the tube to provide a tight grip on the tube surface. This allows for the use of unfair tubing with these connectors.
How do you use a compression nut?
The pipe is slid into the fitting (in this case a toilet shutoff valve) and the nut is tightened down. As the nut is tightened, the compression ring is pressed into the seat, causing it to compress against the pipe and the compression nut, providing a watertight connection. Usually, that is.
Should you use Teflon tape on compression fittings?
On NEW compression fittings, PTFE tape is NOT REQUIRED although there are many people that still use it as an added layer of protection against leaks.
What size wrench is needed for a 3/8 compression fitting?
If the 5/8″ open end wrench fits, BINGO, you have a standard 3/8′ toilet supply valve. Yes, it fits!
