2 Answers
- Pick up a small bucket of an all purpose patch likeDap Flexall All Purpose Filler. …
- Remove the switch cover.
- Using a taping knife, fill in the holes by pushing the compound into the hole and drawing the knife away from the hole.
Nov 17, 2011
How do you fill gaps around a light switch?
Remove the cover plate. If the gap between the electrical box and the drywall is less than 1/4 in., fill it with acrylic latex caulk. If the gap is bigger and lopsided, use foam sealant that’s formulated for use around doors and window framing. The minimally expanding foam won’t drip down your walls.
How do you cover a hole in a light switch?
Quote from the video:
So the faceplate of the light switch was five by five inches. And you're going to try to Center. That then get out your drill. And make four holes in the corners of that square.
How do I fix a hole next to a light switch?
Quote from the video:
Make sure it covers the holes. On both sides. Now you want to hold it in place and just take your 6-inch taping knife and go around the perimeter squeezing out the joint.
Can you caulk around light switch?
Windows get the caulk treatment but for switches and sockets, just loosen off a tad, clean and paint, no caulk around them, they are fitted with screws as they need to removable.
What to use to fill gaps around sockets?
Quote from the video:
Put some polyfill around it it's good stuff because even when it dries off you can carve it. And as long as you're careful.
How do you fill gaps around sockets?
Quote from the video:
Making sure we always shake any excess off before I put the brush. Inside. That's it and again you don't want to be using a lot because you'll have master remove.
How can I hide the gaps around my ceiling light box?
Quote from the video:
So go ahead and get your wires ready and make sure before you do any electrical work you shut the power off at the electrical box so we're going to take the trim for the light.
Should I caulk around light fixtures?
Insulation. The primary purpose of caulk is to help seal a seam, hole or crack against outside weather. This is why builders caulk around windows and doors. If your ceiling or wall is insulated, it’s rarely necessary to caulk your light fixture against cold air.
Should I caulk around electrical outlets?
Holes drilled through studs and top and bottom plates should be caulked or foam sealed to prevent air from following the wiring through wall cavities. Be sure to schedule caulking of electrical penetrations after the wiring has been installed and before the drywall is completed.
Can you use silicone around electrical wires?
Silicone creates an extremely tight and durable seal while also retaining its flexibility, making it a perfect outer coating for electrical wires that may need to be moved or rearranged in the future. In addition to being water- and weatherproof, it can also withstand very high temperatures.
Can I caulk around electrical panel?
Do you have siding installed behind the electrical panel? If there is siding behind the panel, then do not caulk it to the siding. If there is no siding behind the panel, then you can caulk the outside perimeter of the panel.
Can I use expanding foam around electrical cables?
You have to consider if using foam is safe if you have anything routed inside the cavity, such as electrical wiring. So, if you were wondering whether expanding foam damages wiring the answer is yes. Expanding spray foam without carefully planning can damage electrical wiring.
Is expanding foam safe around electrical outlets?
Don’t Get Foam Inside the Box
Be careful when applying foam around electrical wiring and boxes. Don’t let foam get inside the electrical box. It will harden around the box’s parts and cause major problems. Remember, the chemicals in spray foam are flammable.
Where should you not use expanding foam?
When NOT to Use Spray Foam Insulation
- For areas that are too close to electrical boxes:
- For areas too close to ceiling light boxes:
- Open-cell spray foam on your roof:
- For closed-cavity spaces:
- If you have a history of skin, respiratory, or asthma problems:
Mar 29, 2019
Can I put filler over cables?
As others have said, its a bodge, and potentially dangerous. Over time the filler will corrode the copper making the join unsafe. The best remedy would be to pull in (or chase in) a new cable to a point where it can be safely joined as joins cemented into the walls are far from ideal.
How do you fill holes in wires?
Quote from the video:
And tools of choice is some gyprock easy fill 60 a caulking gun silicon any color because you're not going to see it a cork board filling knife some 80 grit sandpaper. And a dust brush.
How do you plaster over cables?
Quote from the video:
Just some stuff a lot from wigs ages ago it's last a long time so I've actually mixed it up to the consistency of milk. So that's four or five parts water to one part PVA.
