How do you remove a stuck pillow block bearing?
Quote from the video:
Quote from Youtube video: This will often cause scratches or gouges on the shaft destructive methods such as a hand grinder acetylene torch or really big hammers are used to remove the bearing.
How do you remove evaporative cooler bearings?
Quote from the video:
Quote from Youtube video: Looks pretty dried out this is a bearing that was closest to the pulley pull that. I took off. This is the other bearing right here on the other side looks a little bit. Better.
How do you get rid of spider bearings?
Quote from the video:
Quote from Youtube video: And fits right on the shaft behind the bearing slides freely and all you have to do at this point is grab hold of the bearing Buster on both handles.
How do you lubricate swamp cooler bearings?
Quote from the video:
Quote from Youtube video: You ever need to grease the bearings. On a swamp cooler. Then just come up and hopefully you can see that that that pops up right there pops up right here it's on either side there's one here.
How do you get a bearing out without a puller?
Quote from the video:
Quote from Youtube video: When I put it in the oven. And I poured a well on the the pinion nut and the bearing. So that shrunk it just enough so that there was enough clearance to knock it out easily.
Can you use WD 40 on swamp cooler?
Do not use wd-40. Wd-40 is a penetrant not a lube. You need machine oil.
Do swamp coolers need to be oiled?
Note that most swamp cooler units have sealed bearings that do not require added lubrication. If you have an old unit that has a lubrication port on the top of each bearing (usually there is one bearing on each side of the fan), this is an indication that you need to lubricate the bearings.
Why is my swamp cooler making a loud noise?
Clicking Noises Could Be From Loose Parts
When the float valve gets loose or loses its seal, it can move around and make loud clicking and clattering noises. This problem is easy to fix by replacing the valve if needed or just repositioning it. Tubes that get loose might also cause a similar sound.
How tight should the belt be on a swamp cooler?
It should not be too tight or too lose. Incorrect fan belt tension could cause your swamp cooler motor to overheat. Roughly speaking there should be about 1 inch of play in the tension of your fan belt.
What kind of oil do you use for a swamp cooler?
Zoom spout oil is high-grade turbine oil. Use it for evaporative cooler bearings and motors. The bottle features a spout with an extra reach for oiling in tight places.
Can I run my swamp cooler all day?
A swamp cooler can be in operation for 24 hours of the day, but you will need to ensure it has enough water. Continuous flow coolers will automatically work and will be fine to run all day. Manual swamp coolers require you to add water to the reservoir and change the settings so it will run all day efficiently.
How do you remove rusty bearings?
Quote from the video:
Quote from Youtube video: Air chisel with all the bits you get the round bit the blade bit all the bits. And all you do is you just come in under the wheel bearing on a slight angle up.
How do you extract bearings?
Quote from the video:
Quote from Youtube video: Sometimes you can just hold it with your hand remember don't bash just tap because the bearing is seated in there nice and squarely so underneath small taps a little bit at a time.
How do you make a puller tool?
Quote from the video:
Quote from Youtube video: And here's all your bits to make your bearing puller tool the bolt and three nuts either metric 10 or 3 8 of an inch it's much of a muchness. The length of the bolt anywhere between 120.
How do you make a homemade bearing press?
Quote from the video:
Quote from Youtube video: So you put take your bolt. Put your washers on. It. Then you save your other washers and your other nut. You put the bolt through the thing that you're working on. But bearing in it.
How do you use a bearing puller tool?
Quote from the video:
Quote from Youtube video: Select two of the same length poor legs from the kit. Use the shortest legs possible to clear the shaft. Thread. One end of the leg into the poor locate. The yoke over the other ends. And tighten.
What are the three types of pullers?
These pullers include bearing splitter plates, 2 and 3 arms bearing pullers, internal bearing pullers, bar type puller &slide hammer puller.
Which bearing puller is best?
Top Bearing Pullers
- 3 Jaw Puller Adjustable Bearing Puller Carbon Steel Gear Puller Suitable.
- DAYUAN 12pcs Bearing Separator Puller Set.
- Orion Motor Tech Blind Hole Collet Bearing Race and Seal Puller Extractor Kit.
- BILITOOLS 15-Piece Bearing Puller Kit Ball Bearing Extractor Bearing Removal Tool Set.
What are the types of bearing puller?
Types of bearing pullers include bearing splitter plates, two and three arm bearing pullers and internal bearing pullers.
