How far does a stove need to be away from the wall?

The standard clearance recommended by the National Fire Protection Agency is 36 inches. This means that the back of the stove should be 36 inches away from any combustible material, such as woodwork, unprotected walls, furniture and even firewood.

How much clearance do you need in front of a wood stove?





At least 36 inches of clearance must be allowed between the top of a stove and an unprotected ceiling. Brick or stone provide little or no protection for a combustible wall since they are good conductors of heat.

How do you build a wall behind a wood stove?

Faux Panels. A common way to help protect the wall behind a wood stove and create a backdrop for your stove includes using masonry veneer faux panels. Stone or brick is a common material to use behind a wood burning stove. These panels help create more of a focal point for a room.

How far does wood stove need to be from wall Canada?

Clearance to combustible requirements for non certified radiant wood stove is 1200 mm (48″). A stove with a metal jacket casing requires 900 mm (36″).

How much space do you need around a stove?

Having at least four feet of space between your stove and other appliances is ideal. This will allow you to work over your stove and oven while others are simultaneously using other kitchen staples like a dishwasher or microwave. For electrical reasons, this is also recommended.

How much space do you need on each side of a stove?





A minimum of 12 inches of landing space on one side of the stove, and another 15 inches on the other side, are the required landing area widths. As this is hardly enough room to set a single pot or pan, this should be considered an absolute bare minimum, with greater widths highly recommended.

How do I reduce the clearance on my wood stove?

Clearance should be three times the diameter of the pipe, e.g., a 6-inch pipe needs 18 inches of clearance. Heat shields may be used to reduce the clearance by the same ratio as for the stove. For example, with sheet metal you can reduce the clearance by two-thirds, from 18 inches to 6 inches.

How close can a wood stove be to a heat shield?

Most standards specify one-inch or in some cases 7/8″ of air space behind the heat shield. Some standards specify a 2″ air space.

How far does a hearth have to stick out?

So how far should a fireplace hearth come out? InterNACHI recommends that for fireplaces that have an opening of 6 square feet (0.56 square meters) or smaller, a hearth should extend at least 16 inches (406mm) out into the room from the opening, and by at least 8 inches (203mm) away from the sides.

How close can a wood stove be to cement board?



A combustible floor must be protected by a non-combustible material (like tile, concrete board, or certified to UL-1618 or as defined by local codes) extending beneath the heater and a minimum of 6″ from each side and minimum 16″ from the front face of the stove and minimum 6″ (or the rear clearance to combustibles

What is the required clearance between the floor and a stove food safety?

The FDA Food Code requires that food be stored six inches off the floor, that food be protected during storage, and that there be no pests in the facility to contaminate food.

What is the clearance for double wall stove pipe?

6″



Double wall stovepipe is used when you don’t have 18″ or more clearance from combustibles. Most of the double wall stove pipe allows for 6″ clearance from wall combustibles and 8″ from ceiling combustibles.

What is the minimum clearance above a stove to combustible material?

30 inches

(CMC 921.3. 2): Household cooking appliances shall have a vertical clearance above the cooking top of not less than 30 inches to combustible material or metal cabinets.

How much space should be between wood burning stove and wall?

Starting from the ground up, you will need to place your stove on a non-combustible hearth, be it stone or toughened glass, with a minimum thickness of 12mm. In terms of the distance between the stove’s external surfaces and surrounding walls, the minimum to the rear and sides is 150mm.

How much clearance do you need for triple wall stove pipe?



Triple-Wall Stove Pipe Installation

According to building codes, there must be a 2-inch clearance around your double- or triple-wall chimney pipe.

How high should stove pipe be above roof?

In essence, any chimney, stove pipe or other heating exhaust vent should be 3 feet (1 meter) above the roofline or 2 feet (61 centimeters) above any part of the building in a 10-foot (3-meter) radius.

How do you make a heat shield for a stove pipe?

The easiest way to make air-cooled heat shields for stovepipe is to cut up a piece of single-wall stovepipe. Then, screw the shield to the pipe using 1-1/4″ heat-proof screws and 1″ ceramic or metal heat shield spacers.

Can cement board be used as a heat shield?



Hardi cement board is an inexpensive solution that will form the foundation of an effective heat shield for any application. Hardi cement board is also designed to have ceramic, porcelain or stone tiles installed over it to cover and beautify the heat shield after it is installed.

Can you use sheet metal behind a wood stove?

Installing sheet metal behind a wood stove creates a barrier to protect the wall and reduce fire risks. Wood stoves provide a cost effective way to heat homes. You can save money by cutting and storing wood yourself.