So, for the base: 5,280 ft x 10′ wide x . 5′ deep = 26,400 cu. ft. OR 26,400 cu.
How do I calculate how much concrete I need for my driveway?
Multiply the square footage by the depth in feet to find the volume in cubic feet. You can find volume by measuring length × width × depth. Finally, divide the cubic footage by 27 to find the volume in cubic yards. This is the amount of concrete needed.
How many yards are in a 24×24 concrete slab?
7.11 yards
For example, for a concrete slab that is 24′ X 24′ X 4”, simply enter 4 in the Thickness/Depth field, 24 in the Width field, and 24 in the Length field. Click “Calculate”. Your answer should be 7.11 yards. Note: The Concrete Volume Calculator can also be used to determine yardage for aggregate products.
What’s the formula for figuring concrete?
Use the formula.
Calculating the volume for concrete requires using three dimensions: length times width (which is area) times the height (thickness) or L x W x H. If you are using feet as your standard unit of measurement, this formula will give you the volume of concrete in cubic feet.
How much rock do I need for my driveway?
According to the Home Depot, 4 to 6 inches of rock or gravel is needed for a driveway.
How much does it cost to pour a 24×24 slab of concrete?
between $3,057 and $5,944
A typical 24×24 garage slab costs between $3,057 and $5,944 with prices ranging from $5.31 to $8.31 per square foot for a 4” reinforced slab of concrete, and $6.83 to $10.32 per square foot for a 6” slab of reinforced concrete.
How do you calculate material for a driveway?
To measure the driveway in cubic feet, multiply the length by width by depth. For cubic yards, divide the total cubic feet by 27. Because one cubic yard of gravel is equal to 1.13 tons, you can multiply your total cubic yards by 1.13 to convert this measurement to tons.
How thick should a concrete driveway be?
four inches
As for thickness, non-reinforced pavement four inches thick is standard for passenger car driveways. For heavier vehicles, a thickness of five inches is recommended. To eliminate standing water, the driveway should be sloped towards the street a minimum of one percent, or 1/8 inch per foot, for proper drainage.
How many yards of concrete do I need for a 10×10 slab?
1.3 cubic yards
The amount you will need for a 10 x 10 slab is 1.3 cubic yards, we always add an extra 10% to allow for any slab depth variations or spills that may occur.
How many yards of concrete do I need for a 10×20 slab?
Regarding this, “how much concrete do I need for a 10×20 slab?”, at 4 inches thick, generally you will need approximately 2.44 cubic yards or 66 cubic feet or 1.969 m3 (either 144 bags of 60lb or 111 bags of 80lb) of premixed concrete for a 10×20 slab, at 5 inches thick slab, 3.07 cubic yards or 83 cubic feet or 2.35 …
How many tons of gravel do I need for a 100 foot driveway?
Here are some examples of driveways with a width of 10 feet and a gravel depth of 4 inches: A 50 foot driveway would need approximately 7.72 tons of gravel. A 100 foot driveway would need approximately 15.43 tons of gravel.
How thick should a gravel driveway be?
The ideal thickness of each layer is between 4 to 6 inches. The middle layer should also be angular stones about 2” to 3” in diameter such as our #2 Bluestone. Since the material is angular it locks together providing traction and a stable foundation.
What is the cheapest gravel for a driveway?
Cheapest gravel for driveways. The cheapest gravel for driveways is crusher run, crushed shells, crushed concrete, slate chips, recycled asphalt, and pea gravel, which all cost $15 to $30 per yard, or less than $1 per square foot when purchased in bulk from a quarry.
Is gravel driveway cheaper than concrete?
Is a gravel driveway cheaper than a concrete one? A gravel driveway is a more budget-friendly option than paving with concrete, which runs from $4 to $15 per square foot.
How many square feet will 5 tons of gravel cover?
How much area does 5 tons of gravel cover:- typically, 5 tons of gravel will cover approximately 540 square feet or 60 square yard or 50 square metres area for standard 2 inch depth. A ton of gravel cover around 108 sq ft area for 2 inch depth, so 5 tons of gravel = 108 × 5 = 540 sq ft coverage.
How wide should a driveway be?
How Wide Are Residential Driveways? Primarily, most professionals recommend that you install a 10 feet to 12 feet wide driveway. The standard driveway width for an SUV or conventional pickup truck is 10 feet. Anything less than 10′ wide will likely present difficulties for drivers, even in smaller vehicles.
How wide should a driveway be for 3 cars?
Driveway widths
Plan driveways with a minimum of 10 feet of width for each vehicle. If space allows, use wider spacing for easier walk-about space between vehicles, the driveway, and the sidewalk, and the vehicles and the garage or house.
What is the average square footage of a driveway?
Size: The average 2-car driveway in the U.S. is 16 x 40 feet, or a total of 640 square feet. Many driveways may be larger or smaller, depending on the distance from the garage or house to the street and possible extensions for RV parking.
Do I need permission to make a driveway?
Whether or not you need planning permission for a driveway will depend on your individual situation. In general, if the driveway is to be part of a new build project, then the details of it should form the ‘access’ part of the planning application for the new dwelling.
Does a driveway add value to a house?
You may be surprised to learn that a driveway does add value to your home. On estimate a driveway can increase your property’s value by 5-10%. That is quite a bit for an area you do not really need to pay a lot to revamp.
Can I pave my own driveway?
Making your own asphalt driveway is hard work, and not a job for one person. If you have friends who will help you, it is possible to save a lot of money by doing your own driveway, even after the cost of rental equipment is factored in.
