How do you connect red and blue wires to light?

In your case the red wire should be connected to the hot (black) wire from the junction box, and blue should be connected to the neutral (white) wire from the box. If there is a green, green and yellow, or just bare copper wire, that’s the ground wire.

What does the blue wire connect to in a light fixture?





If the light can be turned on or off from switches at each side of the room, you’ll see a blue wire that connects the electrical circuits for three-way switches. In some cases, it may run through the electrical box where the existing light is installed, but it is only a switch wire and not a wire for the light.

Where does the red wire go on a light fixture?

Normally you’ll see a red wire in places you would expect a ceiling fan. But in places like a bathroom or a wall light, if you see a red wire, it’s a good bet that the red wire is the wire that’s connected to the light switch. So the red wire is probably the one you want.

Can you connect a red and blue wire?

Quote from the video:
Quote from Youtube video: And your installation guide states the neutral connection is optional.

What does the blue and red wire go to?

Blue wire is for the lamp if one is included with the fan. White wire is neutral. Green wire is for the ground. Red wire is sometimes included and acts as a conductor to carry power to the light kit.

Where do you connect the blue white wire?





Antenna and Amplifier Wires: The blue wire connects to the antenna, and the blue wire with white stripes is for the amplifier.

Are blue and red wires the same?

Red wires are hot wires common in a 240-volt outlet or when a wall switch controls the outlet. Blue and yellow wires are hot wires for ceiling fans and three- or four-way switches. White or gray electrical wires are neutral wires.

What is the red wire coming out of my ceiling?

The red wire is the ungrounded (hot wire) conductor of one switch, while the black wire is the ungrounded (hot wire) conductor of the other switch. One switch would energize the red wire in the original installation, causing the fan to turn on. The other is responsible for the black wire to turn on the light.

What wires go together on a light fixture?

Every light fixture is different. There should be at least two wires coming out of the fixture: a white (neutral) wire and a black (hot) wire. In this case, the two were conjoined and covered with protective plastic.

Which color wires go together?



The protective ground is green or green with yellow stripe. The neutral is white, the hot (live or active) single phase wires are black , and red in the case of a second active.



US AC power circuit wiring color codes.

Function Line, 3-phase
label L3
Color, common blue
Color, alternative yellow

Can red and white wires go together?

In the US, the answer would be no, even though I am reluctant to answer this. White is not aggressive. White is neutral, black is 120, green is ground, and red is the other phase of the mains into your house.

Where does the blue wire go on a light switch?

The faceplate of a single, one-way switch has two terminals: “L1” is the terminal to which the neutral core wire is attached – the blue wire (traditionally black, before the change). “COM” or “Common” is the terminal to which the live core wire is attached – this is the brown wire (formerly red).

What happens if you wire a light switch wrong?



But here’s the catch: If you connect the circuit wires to the wrong terminals on an outlet, the outlet will still work but the polarity will be backward. When this happens, a lamp, for example, will have its bulb socket sleeve energized rather than the little tab inside the socket.

What wire goes to common on light switch?

A one way light switch has two terminals which is a common marked as COM or C. The common is for the live wire that supplies the input voltage to the switch. The other terminal is marked as L1 and is the output to the light fixture.

Does it matter which wire goes where on a light switch?

It doesn’t matter as long as you do it the same on both switches. So, if you connect it to the upper right terminal on one switch, connect it to the upper right terminal on the other switch. Connect the second traveler wire to the terminal opposite the red wire terminal.

What is the red wire on a light switch?

What are Red Wires? Red wires are usually used as secondary hot wires. Red wires are also hot and should be clearly marked to avoid the dangers of electrocution. Red wires are commonly used when installing ceiling fans, where the light switch maybe.

Does the red wire connect to black or white?



Attach the black wire to the outlet you want to always be on (usually the top one) and the red wire to the switched outlet. Connect the white wire to either of the chrome screws (remember, they are still joined) and the ground wire to the green ground screw.

When wiring a light switch what Colour is the live wire?

A standard 2-wire lighting circuit is shown in Figure 1. The brown wire is Live (also know as permanent live), this brings the live supply to the switch. The blue wire is known as the Switched Live and takes power to the light. Switched Live is only live when the switch is on (this is where it gets its name from).

What does the red wire connect to?

Red wires are mostly used to connect the home’s power system, and hardwired smoke detectors such that if one alarm goes off, all of them go off. Red wires are used in the installation of ceiling fans, where the light switches may be. Electricians can link a red and black wire or two red wires.

What is the blue wire in electrical?

The blue wire also referred to as the neutral wire, has the function of transferring electricity away from the appliance. The brown wire, otherwise known as the live wire, transfers electricity to the appliance. The combination of these wires is referred to as a circuit.