slide the (now 1″ shorter) 1 1/2″ slip-joint extension up onto the 1 1/4″ tailpiece and hand tighten the nut and washer, from the previous step, to the threaded top of it. slide the trap u-bend back up into place. wiggle everything about until it’s straight and clean.
How do you connect two pipes to a sink?
Quote from the video:
Quote from Youtube video: Connect the waist arm to the tailpiece by tightening the nut and washer to the bent side of the arm. Feed the slip joint nut followed by a slip joint washer onto the waste arm.
How do you connect drain pipes under sink?
Quote from the video:
Quote from Youtube video: Into place take a nut with the threads facing down slide it up the tailpiece on the sink drain while holding the nut into place choose the proper size washer.
How do I extend the plumbing under my sink?
Quote from the video:
Quote from Youtube video: So you need the proper washer insert the retention nut. And the nylon washer. And loosen up there p-trap. And install the extension tail piece. And stole another retention nut.
Can you glue sink pipes together?
Quote from the video:
Quote from Youtube video: If you need a different type of glue you can go ahead get a blue one which might be fast set or heavy duty. And then if you're using a different type of pipe you might need a different glue as well.
Can 2 sinks share the same drain?
In most cases, you can easily adapt the supply and drain pipes to accommodate two sinks, using tee fittings, special valves, extension pipes and hoses. You may have to vent each sink separately, though, depending on your local plumbing codes.
What if new kitchen sink drain doesn’t line up with existing pipes?
In general, if the P-trap doesn’t line up with the drain, you can adjust the length and height of your drainpipes by cutting them or simply slipping them in and out of their fittings.
How do you connect pipes?
Quote from the video:
Quote from Youtube video: Now while the primer is still wet apply a healthy coat of cement to the outside of the pipe. Then move to the inside of the fitting without redoing go for a second dip and hit the outside of the pipe.
What are the pipes under the kitchen sink called?
P-Trap: A P-trap is a two-part pipe under your sink that allows waste and water to pass through.
How do you use a marvel connector?
Quote from the video:
Quote from Youtube video: And so what we're able to do is we'll we'll fill the male threads with pipe dope or pipe thread compound. And we'll screw this down. And this will allow us to go deeper onto the pipe.
How do you join PVC pipes under sink?
Quote from the video:
Quote from Youtube video: And so what you'll need to do is take it out of the wall put the nut on like this and it comes down like that. And it will tighten on here. And here this will connect behind your wall.
How do you connect two PVC pipes without threads?
Quote from the video:
Quote from Youtube video: That you would put onto the one side. And with the adhesive. Put the adhesive on the outside of this and the inside of the female.
How do you screw PVC pipes together?
Here is how to connect PVC together with fasteners:
- Insert the pipe into the fitting. …
- Use a 1/8” drill bill to make a pilot hole about midway where the pipe and fitting meet, into the side of the fitting. …
- Using a power drill or driver, insert a self-tapping, threaded screw into the pilot hole you just drilled.
How do you join two pipes together?
A coupling can be a reducer, or reducing coupling, meaning they reduce flow by joining a larger pipe to a smaller size. Adapters are used when connecting two pipes of different types. For example, an adapter could be fitted on the end of a plain pipe to allow a threaded connection at the other side of the adapter.
How do you join plastic pipes?
Quote from the video:
Quote from Youtube video: I like to use the felt tip marker I not only give myself index marks but I number the joints too so it all goes back together without any confusion prime the pipe in the fitting.
How do you connect two threaded pipes?
Quote from the video:
Quote from Youtube video: Using the proper teflon tape for the application wrap the tape clockwise. Two to three times teflon tape does not have any adhesion. So be sure to wrap the tape tightly to form a solid seal.
How do you connect two metal pipes together?
Quote from the video:
Quote from Youtube video: If you could you could put it down in that way and clamp it or with pipe fits. In there cradles just nice everything butts up together it all lines up and then you just put a couple of clamps on.
How do you join a pipe without welding?
Joining two copper pipes without welding requires you solder a sweat fitting, or coupling, to connect the two pipes. This is done using heat, flux and solder. Soldering uses a flame as welding does, but the difference between the two methods is that soldering does not require heating the pipe until the metal melts.
What is a threaded coupling?
Threaded coupling means the coupling has threads at one or both ends. Socket weld coupling means the coupling with socket at one or both ends.It is a commonly used accessory for industrial pipe connections.
What does a coupling look like?
Quote from the video:
Quote from Youtube video: Another kind of coupling is the steel grit coupling. It's two halves are connected with a continuous grid of flexible steel which locks around the center of the coupling.
What is a pipe adapter?
In plumbing, an adapter is generally a fitting which interfaces two dissimilar parts. The term commonly refers to: any fitting that connects pipes of different materials, including: expansion adapters which have a flexible section to absorb expansion or contraction from two dissimilar pipe materials.
