Where should a water softener drain line be?
Quote from the video:
Quote from Youtube video: And a half air gap above the flood water rim of the laundry sink and you're good to go if you do that just be careful you don't putting jeans or soak some clothes in there overnight.
How far can the drain be from a water softener?
Now comes the tricky bit: where to place the water softener so you do not exceed 20 feet for the drain line. If it’s any help, the brine tank can be located up to 20 feet away from the softener mineral tank. Consider positioning this tank in a garage to make it easier to fill the tank with salt.
Does a water softener need to be near a drain?
Connect the Drain Tubes
Most water softeners require two drain tubes. One of the drain tubes connects to the control valve and is used to void the backwash water during the regeneration cycle. The other drain tube connects to the brine tank and serves as an overflow drain.
What size is the drain tube for water softener?
½”
The industry standard is a ½” polypropylene drain line that is rigid, yet flexible. Many of the Home Improvement Stores sell “Big Box Water Softeners” and “Installation Kits” to get them connected.
Can you drain water softener into yard?
Keep in mind that in some places local rules and regulations might prohibit you from using this option as groundwater might be used as a source for the local drinking water supply. Even if it is allowed, simply discharging your water softener backwash into the ground could damage your lawn.
Should water softener drain into sump pit?
My water softener empties into a sump pit, and the pump needs to run a few times each time the softener runs. Otherwise, the sump only runs if the basement bathroom is used, which isn’t often since the kids went off to college, husbands, etc.
How do you drain a water softener to a sewer line?
Quote from the video:
Quote from Youtube video: There. And we got our air gap fitting here. And then we've got a little uh riser and a stack and uh and then the trap. So that way if anything were ever to happen with the sewage.
How do I connect my water softener to the main line?
Quote from the video:
Quote from Youtube video: And we connect it with a 3 8 compression. Fitting. We make a connection at the softener. And also at the brine. Tank. Connect the drain line to the drain elbow and we secure that with a hose. Clamp.
Why does a water softener drain need an air gap?
Air gap fittings are plumbing code required to mount in the drain line(waste line) of water treatment equipment and their primary purpose is to prevent non-potable water from flowing backwards possibly mixing and contaminating potable (drinking) water.
Should water softener drain into septic?
Water softeners and septic systems
Some of these studies, like the ones that were done by the University of Wisconsin and the National Sanitation Foundation (NSF) concluded that water softeners do not pose a significant threat to septic systems.
How do I build a dry well for water softener discharge?
Quote from the video:
Quote from Youtube video: Okay three plastic panels. We've knocked out all the holes. So that as the water comes in it just disperses into the stone that surrounds it no bottom no bottom but a top.
How do you dig a dry well for drainage?
Quote from the video:
Quote from Youtube video: Now how far down are we going we'll end up going about 8 or 12 inches. Down. All right as we get closer to the perforated. Pipe. We're going to want to go a little deeper. And a little wider.
How deep should a water softener dry well be?
Step 1: Dig the Hole and Trench
Coming out from the downspout, at least 10 feet from the foundation (and 3 feet from any property line), dig a hole about 4 feet deep and wide. With a long-handled shovel, tunnel under the sidewalk and dig a trench 1 foot deep and 6 inches wide that slopes gradually toward the hole.
How big of a dry well do I need for water softener?
On average, a dry well is 30 to 70 feet deep and 3 feet wide. Each of them has metal casings lined with perforated fibers, so you can fill it with gravel or rock if desired.
What if my water softener is too big?
Generally, you should get a water softener that’s slightly bigger for your needs – but not too big. If a water softener is too large for your household, it won’t regenerate often enough, which can damage the resin beads and promote bacterial growth in the tank. Also, big tanks, consume more water and cost more upfront.
What grain of water softener do I need?
Households with three people or fewer typically need a softener with a grain capacity of around 20,000 units. Households with four or more people typically need a softener with a grain capacity of 30,000 units or more.
