How do you make a hidden compartment box?
Quote from the video:
Quote from Youtube video: Once that was done I cut a dado on one edge of the board. And this is going to hold the half-inch piece of plywood that is going to be the bottom of the box. Then I cut another dado in the board.
How do you make a wooden box with sliding lid?
Quote from the video:
Quote from Youtube video: Like a bandsaw box I need to start by cutting off the back and the front in this case it's going to be the bottom and the lid. So I've cut the bottom off pretty thin.
How do you make a wooden box with a hinged lid?
Quote from the video:
Quote from Youtube video: Table sure would come in handy here at this point I just let it fly off the back of the saw. So now we're going to glue up all four sides in the bottom just spread your glue into the joint.
How do you make a hidden hinge box?
Quote from the video:
Quote from Youtube video: And then you can tighten the screw that will expand. The barrel piece so that kind of fills the space that's in and that creates a hidden joint for the latches. Instead of using a traditional latch.
How do you make a fake lower chest?
Quote from the video:
Quote from Youtube video: Bottom of the drawer a hole drilled from beneath will allow us to use a pen a nail or a piece of a dowel as a secret key to lift the false.
How do you make a small lid box?
Quote from the video:
Quote from Youtube video: Alright then you just want to make the box you know I think you make the lid about one-third what the what the box is so we want to go ahead and separate it you know about right in there.
How do you make a Wood slider?
Quote from the video:
Quote from Youtube video: To finish off the slide itself we use two coats of wipe-on poly being shorts sander between four cone back and giving it final coat of varnish. Then to get it attached. We glued it to the sides.
How do you make a small wooden box?
Quote from the video:
Quote from Youtube video: After those panels dried i used one to set the height of my table saw blade. And cut a rabbet the same depth. As those panels were thick on the top and bottom of all of my box pieces.
How do you make a wood hinge?
Quote from the video:
Quote from Youtube video: So I'm gonna use a pair of calipers. And I've milled my lumber to exactly half an inch. So I'm gonna measure 1/4 inch quarter inch get a dead-center use a center punch.
How do you make a wooden dowel hinge?
Quote from the video:
Quote from Youtube video: I do the the you just want to be able to match the wood I matched the dowel to the wood in the box and then your hinge can be completely hidden.
How do you make a living hinge box?
Quote from the video:
Quote from Youtube video: And what those are is just a way to take a very rigid material like 8 inch plywood. And bend it in a very tight arc and i'll show you how to do that it's actually quite simple.
How do you make a Glowforge hinge?
Quote from the video:
Quote from Youtube video: I went ahead and immediately cut my first version in eighth inch plywood on our glowforge laser cutter. It was taking quite a bit of pressure to hold its shape.
Why is it called a living hinge?
Living hinges are a type of hinge made from an extension of the parent material (typically polypropylene plastic). They are the thin section of plastic that acts as a connection between two larger plastic sections.
How do you cut a living hinge?
Quote from the video:
Quote from Youtube video: For the vector cutting settings. We used speed up 25% at 100% power and a frequency of 500. The first step is engraving the quote on the surface of the wood it's a pretty simple task.
What is Lattice hinge?
Lattice hinges are formed when a set of parallel, overlapping cuts divide a flat sheet into thinner, linked sections that can deform more easily than the solid sheet.
How do you make a hinge?
Quote from the video:
Quote from Youtube video: They can snap apart. So you can design them in one piece print in place or you can design them to snap together.
