How do you weld a perfect 90-degree angle?

Quote from the video:
Quote from Youtube video: Okay you know what a square is yep check it mixture square never comes out straight all right that's one way to do it. Never play with a magnet.

How do you clean a corner weld?





Quote from the video:
Quote from Youtube video: And this is using a die grinder. So here we've got a tungsten carbide burr on there. And this die grinder is essentially for those of you familiar with a dremel.

How do I make my weld smooth?

Quote from the video:
Quote from Youtube video: I've got my safety gear on and I've set my first pass on the MIG weld any wave with an angle grinder.

How do you grind in tight corners?

Quote from the video:
Quote from Youtube video: And you're forever sitting in a little little tight corners right okay. So what are we going to do that we can use cartridge rolls that's not an issue but actually what we've done is in this case we'

Where do you start a weld when welding a corner?

Quote from the video:
Quote from Youtube video: Now what I like to do and this is just my preference I like to start a tack down in that corner.

How do you prepare an outside corner for welding?





Quote from the video:
Quote from Youtube video: And melted those corners off and left a nice weld profile there and the one where I turned it down I'll swab it now and we'll see what we got. There. And as that starts to reveal.

How do you clean welded joints?

After a joint is welded, do not use compressed air to blow away excess material from the joint. This contains moisture and oil contaminants that will introduce new impurities to the surface. Instead, another solvent should be applied and then a stainless steel wire brush should be used to clean the weld.

What is the tool used for cleaning welds?

The chipping hammer has served the welding industry well for many years as the basic tool for removal of slag from Shielded Metal Arc Welding and Flux Core Arc Welding.

How do you hide welding marks?

Quote from the video:
Quote from Youtube video: It on like that. And then you know heat this up if you need to or just hammer the ants close. And then tack it and you're good to go you've hidden the weld. And this is in place.

Does grinding down weld weaken?



I’ve been discussing with a friend of mine whether or not it’s ever OK to grind your welds. I understand that grinding down a weld reduces it’s strength, and therefore a structural weld should never be ground down.

Why grinding is done after welding?

Initial weld grinding. The first stage of weld finishing is the same; the removal of excess stock from the weld itself. The aim here is to grind the joint down to a level and continuous surface with the rest of the parent metal.

How do you get rid of excess welding?

Usually, you can undo welding using torch cutting, plasma cutting, drills, grinding or circular saws, or oxy-acetylene torches. There are a couple of ways to perform this other than just applying a strong force to the weld. The procedure of removing welds relies on the weld type you would like to undo.

How do you wrap corners in welding?



Quote from the video:
Quote from Youtube video: Across here this is dis just a little bit it got a little more penetration. I think in there. You know because I was going a little faster strung it out a little bit more.

What is the strongest weld joint?

TIG welding is often considered the strongest weld since it produces extreme heat, and the slow cooling rate results in high tensile strength and ductility. MIG is also an excellent candidate for the strongest type of weld because it can create a strong joint.

How do you stick weld in a corner?

Quote from the video:
Quote from Youtube video: And here I'm trying to just just go wide enough. So that the weld consumes that corner. And it looks to me like I'm kind of stepping out maybe a little bit too far each time. But we'll see how it.

When would you use a 6013 welding rod?

The 6013 electrode is best used for light to medium penetration on thin or sheet metal pieces. 6013 electrodes are commonly used in manufacturing truck frame bodies, metal furniture, storage tanks, farm implementations, or where aesthetics are of grave importance.

How many passes should be made on an outside corner weld?



Only one weld pass is required for fusing base metal. is sometimes required if the metal is thick, since more than one weld pass is required to make a strong joint with complete penetration.

What is a Philip weld?

Quote from the video:
Quote from Youtube video: Against weld specifications is with a Philip weld gauge. These gauges come in a variety of sets with sizes ranging from one eighth of an inch to three inch in both inch and metric sizes.

What are the 5 types of weld?

There are five basic welding joint types commonly used in the industry, according to the AWS:

  • Butt joint.
  • Tee joint.
  • Corner joint.
  • Lap joint.
  • Edge joint.


Can you reheat welding rods?



Quote from the video:
Quote from Youtube video: You gotta let them go but if they've been sitting in your shop. For. Longer than six months if you want to do a nice well jobs pop them in the oven you're good to go.