How do you use Hayward ColorLogic light control?

Quote from the video:
Quote from Youtube video: Between a yellow and purple and just various colors and you've got different light shows built in whenever you pick a color that you'd like to settle. On simply push in on the knob.

How do I sync my Hayward ColorLogic pool lights?

To re-synchronize your lights, turn the switch on, then back off, then wait between 11 and 14 seconds and turn the switch back on. When the lights come back on, they should enter program #1, and be synchronized. Refer to the included color card as a quick reference to the available programs.

How long do Hayward ColorLogic lights last?

50,000 hours

How long does the light last? The life expectancy for a Colorlogic light is 50,000 hours. The light will perform for over 10,000 hours without any noticeable loss of brightness.

How do I remove a Hayward ColorLogic pool light?

Twist the trim ring clockwise until it firmly locks. The Hayward logo should now be in the 12 o’clock position (Figure 3). To remove the Universal ColorLogic/CrystaLogic LED Light from the LFGUY1000 Niche: Remove the trim ring by turning it counter clockwise.

How do I synchronize my pool lights?

Quote from the video:
Quote from Youtube video: So on and off on and off on and off. In about a one-second interval yeah and the lights will eventually synchronize themselves to the same color. And then you're good to go it's that simple that's.

How do I control the color of my pool light changes?

Quote from the video:
Quote from Youtube video: So turn off the light and turn it back on eight times this is blue now turn off the switch. And turn it back on nine times.

How do you fix a Hayward LED pool light?

Quote from the video:
Quote from Youtube video: Cover off and screw and just essentially remove that all off be careful when you're taking that rubber grommet that you don't rip it. Because I'm certain they're not replaceable.

Why is my LED pool light not working?

You might be dealing with a worn-out seal, and you may need to have it replaced. If the lighting itself is the problem, you may need to buy new LED lights, especially if it’s been damaged. If you’re dealing with a blown bulb, you’ll also need to get that replaced.

Why won’t my pool lights change color?

Motors. Some pool lights that change colors rely on small motors that rotate a multicolored lens so different portions of the lens filter the light being emitted by a single bulb. These lights are susceptible to motor failure, which will allows them to function normally but without any color change.

Can you replace the bulb in a Hayward ColorLogic pool light?

ColorLogic® 120V LED Replacement Bulbs are a quick, cost-effective way to upgrade standard incandescent pool lights to vibrant, color-rich, energy-efficient LEDs. Installation does not require rewiring or fixture replacements.

How do I change my pool light without draining?

Quote from the video:
Quote from Youtube video: So all we have to do is get a phillips screwdriver. And we go to the top screw it's usually 12 o'clock. And we put our screwdriver in here and we remove. This top screw.

How do you change an inground pool light?

Quote from the video:
Quote from Youtube video: You'll need a phillips head screwdriver. There's one phillips head screw located in the top of the light you'll remove that out of the metal ring and the entire unit will slide out of the wall.

How do I pair my LED remote?

Quote from the video:
Quote from Youtube video: One push of the button and it's going to turn. On. You can put it on auto or go through the different colors. Strip them flash for you.

How do you sync lights on Hayward Pro Logic?

Quote from the video:
Quote from Youtube video: How can we sync the lights uh you just go into your lights. And here's your color lights. And then turn them on and then there is a if you're in the newer. Software.

How do I program my Hayward omnilogic lights?

Quote from the video:
Quote from Youtube video: If I push that icon. There's my menu for my pool light specifically. I can turn it on/off with the toggle switch I have a schedule icon. So if I push that I can add a schedule to my pool lights.

How do you set up a Hayward Pool controller?

Quote from the video:
Quote from Youtube video: Okay select body of water. And press the right arrow to configure. So what we'll do is obviously the first one's already selected so we're going to hit the right arrow.

How do I calibrate my Hayward OmniLogic screen?

A series of five boxes will appear, touch the center of each box to calibrate the screen. Locate and tap on “RemoveDDT” AND power cycle the OmniLogic. On the right of the dashboard locate and tap the “config” icon. The DDT (device discovery table) holds a list of all the smart devices the MSP talks to.

How do you program a Hayward system?

Quote from the video:
Quote from Youtube video: So we'll start it off in a high setting. So you just hit plus. It will run in at 2,300 rpm once you get that set you hit over and then you want to set the time for when you want it to turn on.

How do I unlock my Hayward configuration menu?

Quote from the video:
Quote from Youtube video: Here you hit the menu button oh it's locked it says so you have to hit these two arrow buttons hold them down. Boom we are in to the configuration.

What RPM should I run my variable speed pool pump?

I suggest running your pump on a higher setting for an hour or two. This would be somewhere in the high 2,000 RPMs. This will allow a good mixture of your chemicals, your automatic pool cleaner to run around, and get a good portion of your pool water through the filter.