You can easily make the hole smaller using mesh tape and joint compound. Put half of the mesh on the wall all the way around the hole and add as much mud as possible onto tape, then smooth. Might be able to make another pass the next day.

How do you make a drywall hole smaller?

Tiny nail and screw holes are the easiest to fix. Use a putty knife to fill them with spackling or wall joint compound. Allow the area to dry, then sand lightly. Anything larger must be covered with a bridging material for strength before patching compound can be applied.

How do you fix a drywall hole that is too big?





Fill the hole with any liquid glue that can be used on wood (like Elmer’s). Jam in several wood toothpicks until they’re very snug and entirely fill the hole. Allow to dry completely, then snap off toothpick ends so they’re flush with surface. Drive your screw through the repaired hole!

How do I fix the hole size in my wall?


Quote from Youtube video: And just be careful don't push too hard you don't want to blow through. And cause any screws to blow. Out. Make sure it fits nicely carefully add some screws at least one on each corner.

How do you fix a 1 inch diameter in drywall?

Quote from the video:
Quote from Youtube video: If the hole is under 1/2 inch you can just apply patching spackle without adding drywall mesh tape holes shown in the example is about one inch in diameter.

How do I make a hole smaller?

Using Matches or Toothpicks



The most common – albeit not professional – way to fill screw holes when you need to make them smaller is by using matches or toothpicks as shims. This method has been used for a long time, but should only be used for holes that won’t hold any great weight.

How do I make my ceiling hole smaller?





The easiest way to do this is by screwing two support sticks above the drywall to span the hole. Use drywall screws driven through the surrounding drywall to hold the support sticks in place, then cut a drywall patch disk to fit the hole.

How big of a drywall hole is too big to patch?

For larger holes in your drywall that are bigger than four inches in diameter, you won’t be able to use putty or spackle to repair them. When repairing larger drywall holes, you’ll likely need to cut out some of the existing drywall.

Can I use drywall tape to patch a hole?

Quote from the video:
Quote from Youtube video: If the hole is under 1/2 inch you can just apply patching spackle without adding drywall mesh tape holes shown in the example is about one inch in diameter.

What size hole is too big to patch?

Puncture repairs are limited to the crown area of the tire, which is the center of the tread approximately 1 to 1.5 inches in from each shoulder. Puncture repairs are also restricted by size and cannot be larger than 3/8 of an inch in diameter.

Can you cut drywall patch?



Patches can be cut or overlapped as needed. Trowel on the first coat of joint compound over the patch, spreading the compound flat enough to see the outline of the mesh through it (Photo 2).

Is spackle strong enough to hold a screw?

A drywall hole that has been filled with spackle will not support a screw. Spackle, also known as joint compound or “drywall mud,” is not as durable as true drywall. Joint compound will shrink and pulverize easily when a screw is driven into it.

How do you make a screw hole smaller?

Quote from the video:
Quote from Youtube video: You can easily fix this by simply inserting a small diameter piece of timber. Such as a matchstick cocktail stick or a wooden skewer.

What household items can I use to patch a large hole in the wall?



Mix a tablespoon of flour, a teaspoon of salt and a few droplets of water in a small container. Mix thoroughly until it forms a paste and apply to the hole or crack as you would joint compound. Use a putty knife or index card to remove the excess while it is still wet and allow the rest to dry.

How do you move a slightly screw hole?

Quote from the video:
Quote from Youtube video: Life likely to be softer than the actual window frame itself I'm now going to just gently tap that match into the hole. This is why I wanted to make match take a little bit shorter than the screw.

How do you fill and reuse a screw hole?

Quote from the video:
Quote from Youtube video: And get some toothpicks for this hole right here three ought to do it just place them in the hole. Like that break off the excess.

Can you screw into wall filler?

Polycell Deep Gap Polyfilla is the easy way to fill deeper holes, up to 20mm, in one application. Easy to sand for a smooth finish. Fills holes up to 20mm and accepts nails or screws.