How do you remove lead solder from cast iron pipe?
Drops of lead will start to fall from the ring. Eventually the cast iron pipe itself will get hot enough that it will melt the lead touching the pipe. Now you can use a screwdriver or chisel to pry the entire ring of lead out of the pipe.
How do you remove a stuck cast iron plug?
How to Loosen a Cast Iron Clean Out Plug
- Spray lubricant around the rim of the plug, aiming the spray to get as much of it into the threads as possible. …
- Tap the rim of the plug a few times with a hammer to loosen the threads, instructs Family Handyman.
How do you remove lead from cast iron joint?
Quote from the video:
Quote from Youtube video: And chiseling it with a screwdriver. And just a whole lot of mess. But i'm sure we're gonna have a mess too but what i'm gonna use is map gas.
How do you remove lead cleanout plugs?
Slip one pipe wrench onto the fitting and the second one on the cleanout plug. Then give it all you’ve got. If the plug breaks loose, you’re home free. Start cleanout plug removal by applying gentle heat to the cleanout plug and fitting to soften the old pipe dope (Photo 1).
How do you loosen a stuck pipe fitting?
Quote from the video:
Quote from Youtube video: Fitting use a regular propane or map gas torch to get it nice and hot. And then take the joint apart while it's still heated. That will make it a lot easier since the fitting expands.
How do you repair cast iron lead oakum joint?
Linda Cottin
- Step 1: Remove lead and oakum remnants from the joint to be packed. …
- Step 2: Loosely roll the oakum to form a workable length. …
- Step 3: Insert the smaller pipe into the hub. …
- Step 4: Use a packing iron, dull chisel or wide, flat screwdriver to pack the oakum evenly into the pipe joint.
What is a clean out plug?
A cleanout plug is a cap or lid used to close off a drain cleanout pipe. The term cleanout or cleanout pipe may refer to any branch of a plumbing pipe that is used for cleaning or unclogging the system.
How do you remove a cast iron P trap?
Quote from the video:
Quote from Youtube video: Because it's cast-iron I can hit it and it should break that fitting. Ready. There's okay that's loose now let's strike okay back and go where it belongs outside.
How do you plug in a cast iron drain pipe?
Quote from the video:
Quote from Youtube video: You zip ties to mark the cut around the pipe. And add strapping to support both sides to cut use a reciprocating saw with a metal cutting blade rated for cast iron.
How do you remove the knockout Test cap?
Quote from the video:
Quote from Youtube video: So you gotta take it again that's why this really fine screwdriver and pry it up you know the thing that would work really good is a a paint ring or a paint. Tool the opens paint cans.
How do you use a cleanout plug?
Quote from the video:
Quote from Youtube video: And the handle is pointing up when the rubber pad is in place to seal the top of the cleanout. Then push down on the handle until the foot engages on the cleanout.
How do you remove a square pipe plug?
If a square head plug is to be removed, pound on the head of the plug using a one pound hammer. Rhythmic blows, not too hard, should be used and continued for a minute or more. A spray penetrant, like WD-40, always helps. Use a large wrench, like a 12″ crescent to remove the plug.
Do they make square sockets?
Sockets & Drivers for Square head Bolts
Try using a socket that fits the number of corners on your square head bolts. These Square Socket or 4-point sockets fit many of the common head sizes we sell. Sockets for square head bolts and Square Nuts. Bolts and screws are classified by their shank or shaft size.
How do you remove a stuck galvanized pipe?
- Step 1: Shut Off the Water. …
- Step 2: Apply Penetrating Oil. …
- Step 3: Loosen the Pipe Union Nearest the Target Fitting. …
- Step 4: Cut the Pipe Entering the Fitting. …
- Step 5: Hold the Fitting in Place. …
- Step 6: Turn the Pipe Wrench to Remove the Pipe. …
- Step 7: Remove the Pipe From the Other Side.
- Remove enough wall covering to access all the rusted pipes. …
- Shut off the water to the pipes. …
- Cut out the rusted section with a reciprocating saw and a 6-inch metal-cutting blade. …
- Unscrew the ends of the pipes from the fittings with a pair of pipe wrenches.
How do you loosen old galvanized pipe fittings?
Quote from the video:
Quote from Youtube video: After he gets completely hot grab your pipe wrench. Or your channel locks whatever you have start putting some force on this thing. It should come right apart you shouldn't have any.
How do you remove old galvanized pipe fittings?
Quote from the video:
Quote from Youtube video: You can take the sawzall. With a metal cutting blade it will cut through that galvanized pipe. And get that about the two or three inches from the where.
How do you remove old rusted galvanized pipe?
How to Remove Rusted Galvanized Pipe From a Wall
Can you heat galvanized pipe to loosen?
Heat. You can apply heat to a galvanized pipe using a torch. Apply the torch to the joint of the pipe in order to loosen it. While heating the pipe, you can use a pipe wrench to twist it loose.
